Fluke N4K 2PP42I Product Manual - Page 75

Introduction, Prior to Measuring, Measuring with Default Configuration

Get Fluke N4K 2PP42I PDF manuals and user guides View all Fluke N4K 2PP42I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

8 Measuring Process Introduction Introduction The Fluke NORMA 4000/5000 Power Analyzer is designed for the measuring of currents and voltages for up to three different channels. The Power Analyzer calculates rms values, real, apparent and reactive power, and other derived values. The accuracy is not affected by the wave form, frequency, or phase shift. Harmonics may be displayed to a maximum of half the sampling frequency. Default settings are available for loading quick setups. In addition, you can define more specific settings to save and load as required (see, "Configuration" in Chapter 7). The Power Analyzer begins a measurement as soon as the configuration is set and the device is switched on. Prior to Measuring Connect Power Analyzer to the mains (power) socket. 1. Check the measuring connections at the Power Analyzer. 2. Switch on the Power Analyzer. Measuring with Default Configuration If the default configuration is acceptable, no additional steps are required. Ensure that the factory configuration is loaded (see, "Load Configuration" in Chapter 7). Measuring with User-Defined Configuration If custom analysis is required, load the respective configuration (see "Configuration" in Chapter 7). Note If measurements with an external shunt or probe are required, make sure that there is no signal connected at the direct current inputs. Signals on both inputs (external- and direct-current input) can damage the measurement unit. 8-3 MyFlukeStore Shop for Fluke products online at: www. .com 1.888.610.7664

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
Measuring Process
Introduction
8
8-3
Introduction
The Fluke NORMA 4000/5000 Power Analyzer is designed for the measuring of currents
and voltages for up to three different channels. The Power Analyzer calculates rms
values, real, apparent and reactive power, and other derived values. The accuracy is not
affected by the wave form, frequency, or phase shift. Harmonics may be displayed to a
maximum of half the sampling frequency.
Default settings are available for loading quick setups. In addition, you can define more
specific settings to save and load as required (see, "Configuration" in Chapter 7). The
Power Analyzer begins a measurement as soon as the configuration is set and the device
is switched on.
Prior to Measuring
Connect Power Analyzer to the mains (power) socket.
1.
Check the measuring connections at the Power Analyzer.
2.
Switch on the Power Analyzer.
Measuring with Default Configuration
If the default configuration is acceptable, no additional steps are required.
Ensure that the factory configuration is loaded (see, "Load Configuration" in Chapter 7).
Measuring with User-Defined Configuration
If custom analysis is required, load the respective configuration (see "Configuration" in
Chapter 7).
Note
If measurements with an external shunt or probe are required, make sure
that there is no signal connected at the direct current inputs. Signals on
both inputs (external- and direct-current input) can damage the
measurement unit.
Shop for Fluke products online at:
1.888.610.7664
www.
MyFlukeStore
.com