Fujitsu FPCM20654 User Guide - Page 45

Memory Upgrade, Module

Get Fujitsu FPCM20654 PDF manuals and user guides View all Fujitsu FPCM20654 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

User-Installable Features Memory Upgrade Module Your Fujitsu LifeBook P Series notebook/Tablet PC comes with a minimum of 256 MB of high speed Double Data Rate Synchronous Dynamic RAM 2 (DDR2 SDRAM), 400 MHz factory installed. To increase your system's memory capacity, you may install a memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. To ensure 100% compatibility, purchase the SDRAM module only from the Fujitsu web store at www.shopfujitsu.com. Do not remove any screws from the memory upgrade module compartment except those specifically shown in the directions for installing and removing the module. INSTALLING MEMORY UPGRADE MODULES 1. Turn off power to your LifeBook notebook/Tablet PC and remove any power adapter (AC or auto/ airline). 2. Make sure that all the connector covers are closed. 3. Turn the system bottom side up, and remove the screws of the memory upgrade module compartment. (Figure 4-2) 4. Remove the cover. 7. Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is properly in place. Figure 4-3. Installing a Memory Module 8. Replace the cover. (Figure 4-4) 9. Replace the screws. Figure 4-4. Replacing the Memory Compartment Cover The memory upgrade module is not something you routinely remove from your notebook/Tablet PC. Once it is installed, you should leave it in place unless you want to change system memory capacity. Figure 4-2. Opening the Memory Upgrade Compartment 5. Remove the memory upgrade module from the static guarded sleeve. 6. Align the memory upgrade module with the component side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment. (Figure 4-3) REMOVING A MEMORY UPGRADE MODULE 1. Perform steps 1 through 4 of Installing a Memory Upgrade Module. 2. Pull the clips sideways away from each side of the memory upgrade module at the same time. 3. While holding the clips out, remove the module from the slot by lifting it up and pulling towards the rear of your notebook/Tablet PC. 4. Store the memory upgrade module in a static guarded sleeve. 5. Replace the cover. (Figure 4-4) 6. Replace the screws. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
39
User-Installable Features
Memory Upgrade
Module
Your Fujitsu LifeBook P Series notebook/Tablet PC comes
with a minimum of 256 MB of high speed Double Data
Rate Synchronous Dynamic RAM 2 (DDR2 SDRAM),
400 MHz factory installed. To increase your system’s
memory capacity, you may install a memory upgrade
module. The memory upgrade must be a dual-in-line
(DIMM) SDRAM module. To ensure 100% compati-
bility, purchase the SDRAM module only from the
Fujitsu web store at www.shopfujitsu.com
.
INSTALLING MEMORY UPGRADE MODULES
1.
Turn off power to your LifeBook notebook/Tablet
PC and remove any power adapter (AC or auto/
airline).
2.
Make sure that all the connector covers are closed.
3.
Turn the system bottom side up, and remove the
screws of the memory upgrade module compart-
ment.
(Figure 4-2)
4.
Remove the cover.
Figure 4-2. Opening the Memory Upgrade Compartment
5.
Remove the memory upgrade module from the
static guarded sleeve.
6.
Align the memory upgrade module with the
component side up. Align the connector edge of the
memory upgrade module with the connector slot in
the compartment.
(Figure 4-3)
7.
Insert the memory upgrade module at a 45° angle.
Press the connector edge of the module firmly down
and into the connector until it lodges under the
retaining clip. You will hear a click when it is prop-
erly in place.
Figure 4-3. Installing a Memory Module
8.
Replace the cover.
(Figure 4-4)
9.
Replace the screws.
Figure 4-4. Replacing the Memory Compartment Cover
REMOVING A MEMORY UPGRADE MODULE
1.
Perform steps 1 through 4 of Installing a Memory
Upgrade Module.
2.
Pull the clips sideways away from each side of the
memory upgrade module at the same time.
3.
While holding the clips out, remove the module
from the slot by lifting it up and pulling towards the
rear of your notebook/Tablet PC.
4.
Store the memory upgrade module in a static
guarded sleeve.
5.
Replace the cover.
(Figure 4-4)
6.
Replace the screws.
Do not remove any screws from the
memory upgrade module compartment
except those specifically shown in the
directions for installing and removing the
module.
The memory upgrade module is not
something you routinely remove from
your notebook/Tablet PC. Once it is
installed, you should leave it in place
unless you want to change system
memory capacity.