Fujitsu MBA3073NC Product Manual - Page 55

Use No.6-32UNC.

Get Fujitsu MBA3073NC - Enterprise 73.5 GB Hard Drive PDF manuals and user guides View all Fujitsu MBA3073NC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

(1) Mounting screw Use No.6-32UNC. (2) Mounting frame structure Special attention must be given to mount the HDD as follows. a) Use the frame with an embossed structure, or the like. Mount the HDD with making a gap of 2.5 mm or more between the HDD and the frame of the system. b) As shown in Figure 4.4, the inward projection of the screw from the HDD frame wall at the corner must be 4.5 mm ± 0.8 mm. c) Tightening torque of screw must be secured with 0.59N·m (6kgf·cm) ±12%. d) Impact caused by the electric screwdriver must be within the HDD specifications. e) Must be handled on an anti-static mat. Figure 4.4 Mounting frame structure (3) Limitation of side-mounting Use the four screw holes at the both ends on the both sides as shown in Figure 4.5. Do not use the center hole by itself. In case of using the center hole, it must be used in combination with two holes on both ends. (Total six screws for six holes enclosed) C141-E270 51 Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
(1)
Mounting screw
Use No.6-32UNC.
(2)
Mounting frame structure
Special attention must be given to mount the HDD as follows.
a)
Use the frame with an embossed structure, or the like.
Mount the HDD with making a
gap of 2.5 mm or more between the HDD and the frame of the system.
b)
As shown in Figure 4.4, the inward projection of the screw from the HDD frame wall at
the corner must be 4.5 mm ± 0.8 mm.
c)
Tightening torque of screw must be secured with 0.59N·m (6kgf·cm) ±12%.
d)
Impact caused by the electric screwdriver must be within the HDD specifications.
e)
Must be handled on an anti-static mat.
Figure 4.4
Mounting frame structure
(3)
Limitation of side-mounting
Use the four screw holes at the both ends on the both sides as shown in Figure 4.5.
Do not use the
center hole by itself.
In case of using the center hole, it must be used in combination with two holes on both ends.
(Total six screws for six holes enclosed)
C141-E270
51
Downloaded from
www.Manualslib.com
manuals search engine