Fujitsu MBA3073NC Product Manual - Page 97

Dismounting HDDs, CAUTION

Get Fujitsu MBA3073NC - Enterprise 73.5 GB Hard Drive PDF manuals and user guides View all Fujitsu MBA3073NC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

a. Control mode parameters Parameter • QUEUE ALGORITHM MODIFIER • QErr: Resume or abort remaining suspended commands after sense pending state Default value 0 (Execution sequence of read/write commands is optimized.) 0 (command is resumed) 5.7 Dismounting HDDs Since the method and procedure for dismounting the HDD, etc. depends on the locker structure of the system, etc., the work procedures must be determined in consideration of the requirements specific to the system. This section describes the general procedures and notes on dismounting the drive. It is recommended before dismounting the HDD to make sure the spindle motor completely stops after power was turned off. CAUTION High temperature To prevent injury, never touch the HDD while it is hot. The DE and LSI become hot during operation and remain hot immediately after turning off the power. a) Remove the power cable. b) Remove the SCSI cable. NC Model uses a single cable for power supply and the SCSI interface. c) When the external operator panel is mounted, remove the cable. If it is difficult to access the connector position, the cable may be removed after step e). d) Remove the DC ground cable. e) Remove the four mounting screws securing the HDD, then remove the HDD from the system cabinet. f) When storing or transporting the HDD, put it the antistatic case (Fcell) (see Section 5.1 and 6.5). C141-E270 93 Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
a.
Control mode parameters
Parameter
Default value
• QUEUE ALGORITHM MODIFIER
0 (Execution
sequence of
read/write
commands is
optimized.)
• QErr:
Resume or abort remaining suspended
commands after sense pending state
0 (command is
resumed)
5.7
Dismounting HDDs
Since the method and procedure for dismounting the HDD, etc. depends on the locker structure of
the system, etc., the work procedures must be determined in consideration of the requirements
specific to the system.
This section describes the general procedures and notes on dismounting
the drive.
It is recommended before dismounting the HDD to make sure the spindle motor completely stops
after power was turned off.
CAUTION
High temperature
To prevent injury, never touch the HDD while it is hot. The DE and LSI
become hot during operation and remain hot immediately after turning off the
power.
a)
Remove the power cable.
b) Remove the SCSI cable.
NC Model uses a single cable for power supply and the SCSI interface.
c)
When the external operator panel is mounted, remove the cable.
If it is difficult to access the
connector position, the cable may be removed after step e).
d)
Remove the DC ground cable.
e)
Remove the four mounting screws securing the HDD, then remove the HDD from the system
cabinet.
f)
When storing or transporting the HDD, put it the antistatic case (Fcell) (see Section 5.1 and
6.5).
C141-E270
93
Downloaded from
www.Manualslib.com
manuals search engine