Fujitsu MBA3073NC Product Manual - Page 8

Alert message, Installation, Diagnostics and, Maintenance, C141-E270 - warranty

Get Fujitsu MBA3073NC - Enterprise 73.5 GB Hard Drive PDF manuals and user guides View all Fujitsu MBA3073NC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Task Installation Diagnostics and Maintenance Alert message Page High temperature To prevent injury, never touch the HDD while it is hot. The DE and LSI 93 become hot during operation and remain hot immediately after turning off the power. Data loss When the SEND DIAGNOSTIC command terminates with the CHECK 98 CONDITION status, the initiator must collect the error information using the REQUEST SENSE command. The RECEIVE DIAGNOSTIC RESULTS command cannot read out the error information detected in the self- diagnostics. Data loss Save data stored on the HDD to other media before requesting repair. Fujitsu 99 does not assume responsibility if data is corrupted during servicing or repair. High temperature To prevent injury, never touch the HDD while it is hot. The DE and LSI 99 become hot during operation and remain hot immediately after turning off the power. Electrical shock 100 - To avoid shocks, turn off the power before connecting or disconnecting a cable, connector, or plug. - Never touch the HDDs while power-feeding. Damage - Always ground yourself with a wrist strap connected to ground before 100 handling. ESD (Electrostatics Discharge) may cause the damage to the device. - To prevent electrical damage to the HDD, turn the power off before connecting or disconnecting a cable, connector, or plug. - Never remove a PCBA. - Never use a conductive cleaner to clean the HDDs. - Ribbon cables are marked with a colored line. Connect the ribbon cable to a cable connector with the colored wire connected to pin 1. - Never open the HDD for any reason. Damage - Never remove any labels from the HDD or deface them in any way. 107 - Never open the DE for any reason. Doing so will void any warranties. 4 Downloaded from www.Manualslib.com manuals search engine C141-E270

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
Task
Alert message
Page
Installation
High temperature
To prevent injury, never touch the HDD while it is hot. The DE and LSI
become hot during operation and remain hot immediately after turning off the
power.
93
Data loss
When the SEND DIAGNOSTIC command terminates with the CHECK
CONDITION status, the initiator must collect the error information using the
REQUEST SENSE command.
The RECEIVE DIAGNOSTIC RESULTS
command cannot read out the error information detected in the self-
diagnostics.
98
Data loss
Save data stored on the HDD to other media before requesting repair. Fujitsu
does not assume responsibility if data is corrupted during servicing or repair.
99
High temperature
To prevent injury, never touch the HDD while it is hot. The DE and LSI
become hot during operation and remain hot immediately after turning off the
power.
99
Diagnostics and
Maintenance
Electrical shock
-
To avoid shocks, turn off the power before connecting or disconnecting a
cable, connector, or plug.
-
Never touch the HDDs while power-feeding.
100
Damage
-
Always ground yourself with a wrist strap connected to ground before
handling.
ESD (Electrostatics Discharge) may cause the damage to the
device.
-
To prevent electrical damage to the HDD, turn the power off before
connecting or disconnecting a cable, connector, or plug.
-
Never remove a PCBA.
-
Never use a conductive cleaner to clean the HDDs.
-
Ribbon cables are marked with a colored line.
Connect the ribbon cable
to a cable connector with the colored wire connected to pin 1.
-
Never open the HDD for any reason.
100
Damage
-
Never remove any labels from the HDD or deface them in any way.
-
Never open the DE for any reason.
Doing so will void any warranties.
107
4
C141-E270
Downloaded from
www.Manualslib.com
manuals search engine