Garmin DriveAssist 50LMT Owner s Manual - Page 6
Installing the Dash Camera Memory Card - gps
View all Garmin DriveAssist 50LMT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
Installing the Dash Camera Memory Card Before the device can record video from the integrated dash camera, you must install a camera memory card. The camera requires a microSD™ memory card from 4 to 64 GB with a speed rating of class 10 or higher. You can use the included memory card, or you can purchase a compatible memory card from an electronics supplier. 1 Insert a memory card into the camera memory card slot . À Á NOTE: If you install the memory card into the incorrect slot, the camera cannot record video. 2 Press it in until it clicks. Connecting the Device to Vehicle Power WARNING This product contains a lithium-ion battery. To prevent the possibility of personal injury or product damage caused by battery exposure to extreme heat, store the device out of direct sunlight. Before you use your device on battery power, you should charge it. 1 Plug the vehicle power cable into the USB port on the À device. 2 Press the mount onto the suction cup until it snaps into Á  place. 3 Press the suction cup to the windshield, and flip the lever à back toward the windshield. 4 Fit the tab on the top of the mount into the slot on the back of the device. 5 Press the bottom of the mount into the device until it clicks. 6 Plug the other end of the vehicle power cable into a power outlet in your vehicle. Turning the Device On or Off • To turn the device on, press the power key, or connect the device to power. • To put the device in power saving mode, press the power key while the device is on. While in power saving mode, the screen is off and the device uses very little power, but it can wake instantly for use. TIP: You can charge your device faster by putting it in power saving mode while charging the battery. • To turn off the device completely, hold the power key until a prompt appears on the screen, and select Off. The prompt appears after five seconds. If you release the power key before the prompt appears, the device enters power saving mode. Acquiring GPS Signals When you turn on your navigation device, the GPS receiver must collect satellite data and establish the current location. in the status bar indicates the satellite signal strength. The time required to acquire satellite signals varies based on several factors, including how far you are from the location where you last used your navigation device, whether you have a clear view of the sky, and how long it has been since you last used your navigation device. The first time you turn on your navigation device, it may take several minutes to acquire satellite signals. 1 Turn on the device. 2 Wait while the device locates satellites. 3 If necessary, go outdoors to an open area, away from tall buildings and trees. When turns green, the device has acquired satellite signals and is ready for navigation. Status Bar Icons The status bar is located at the top of the main menu. The status bar icons display information about features on the device. You can select some icons to change settings or view additional information. GPS signal status. Hold to view GPS accuracy and acquired satellite information (Viewing GPS Signal Status, page 22). Bluetooth® technology status. Select to view the Bluetooth settings (Bluetooth Settings, page 18). Connected to hands-free calling. Select to place a phone call (Hands-Free Calling, page 16). Current time. Select to set the time (Setting the Time, page 19). Battery charge level. Connected to the Smartphone Link app. Select to view connected device and subscription information (Pairing with Your Phone and Connecting to Smartphone Link, page 14). Temperature. Select to view the weather forecast (Viewing the Weather Forecast, page 17). Dash camera recording status. Select to view the dash cam video (Dash Camera, page 3). Using the On-Screen Buttons On-screen buttons allow you to navigate the pages, menus, and menu options on your device. • Select to return to the previous menu screen. • Hold to quickly return to the main menu. • Select or to scroll through lists or menus. • Hold or to scroll faster. • Select to see a context-based menu of options for the current screen. Adjusting the Volume 1 Select Volume. 2 Select an option: • Use the slider bar to adjust the volume. • Select to mute the device. • Select for additional options. 2 Getting Started