Garmin GPSMAP 525 Owner's Manual - Page 64

Can't Read Voltages That Low, Limited To Bottom Of Range, Can't Write User Card, Card May Be Full

Get Garmin GPSMAP 525 - Marine GPS Receiver PDF manuals and user guides
UPC - 753759066116
View all Garmin GPSMAP 525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Appendix Can't Read Voltages That Low, Limited To Bottom Of Range- voltage value in the Battery Alarm setup is lower than the voltage where the unit automatically turns off. Can't Unlock Maps-data on the data card is not unlocked for the unit. Contact your dealer or Garmin Product Support. Can't Write User Card, Card May Be Full-error reading card; remove and reinsert. Contact your dealer or Garmin Product Support if the problem persists. Can't Write User Card, Card Is Read-Only-the SD card in your unit contains data copy protection. Card Needed-Your unit needs to have an SD card inserted into the SD card slot in order to perform the function you requested. DSC Position Report Received From-shows the MMSI or name associated with an MMSI. Database Error-internal problem with the unit. Contact your dealer or Garmin Product Support to have the unit serviced. Deep Water Alarm-the Deep Water Alarm depth has been reached. Directory Item With This MMSI Already Exists-the MMSI number is already in the DSC directory. Use a different number. 58 Directory Memory is Full, Can't Create Entry-the DSC directory has reached the maximum of 100 contacts. Delete unneeded contacts to add new ones. Distress Call-a DSC distress call has been received. Take appropriate action. Entering (Leaving) target water temperature-the target water temperature is 2°F (1.1°C) above or below the temperature specified by the Water Temperature Alarm. These messages appear when you enter or leave that zone. Entering Safe Region-the boat is approaching a safe region as defined by your configuration settings. Entering Unsafe Region-the boat is approaching an unsafe region as defined by your configuration settings. Fish Alarm-a beep sounds (if enabled) when a fish is detected. This alarm does not show a message banner. Invalid MMSI-enter a valid MMSI. Lost Satellite Reception-the unit has lost satellite signals. Check antenna connections or try moving to a location with a clear view of the sky. NMEA Depth Is Below Transducer-you must enter an appropriate Keel Offset for the transducer (page 43). GPSMAP 400/500 Series Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
5¶
GPSMAP 400/500 Series Owner’s Manual
Appendix
Can’t Read Voltages That Low, Limited To Bottom Of Range
—
voltage value in the Battery Alarm setup is lower than the voltage
where the unit automatically turns off.
Can’t Unlock Maps
—data on the data card is not unlocked for the
unit. Contact your dealer or Garmin Product Support.
Can’t Write User Card, Card May Be Full
—error reading card;
remove and reinsert. Contact your dealer or Garmin Product Support
if the problem persists.
Can’t Write User Card, Card Is Read-Only
—the SD card in your
unit contains data copy protection.
Card Needed
—Your unit needs to have an SD card inserted into the
SD card slot in order to perform the function you requested.
DSC Position Report Received From
—shows the MMSI or name
associated with an MMSI.
Database Error
—internal problem with the unit. Contact your
dealer or Garmin Product Support to have the unit serviced.
Deep Water Alarm
—the Deep Water Alarm depth has been
reached.
Directory Item With This MMSI Already Exists
—the MMSI
number is already in the DSC directory. Use a different number.
Directory Memory is Full, Can’t Create Entry
—the DSC
directory has reached the maximum of 100 contacts. Delete
unneeded contacts to add new ones.
Distress Call
—a DSC distress call has been received. Take
appropriate action.
Entering (Leaving) target water temperature
—the target water
temperature is 2°F (1.1°C) above or below the temperature specified
by the Water Temperature Alarm. These messages appear when you
enter or leave that zone.
Entering Safe Region
—the boat is approaching a safe region as
defined by your configuration settings.
Entering Unsafe Region
—the boat is approaching an unsafe region
as defined by your configuration settings.
Fish Alarm
—a beep sounds (if enabled) when a fish is detected.
This alarm does not show a message banner.
Invalid MMSI
—enter a valid MMSI.
Lost Satellite Reception
—the unit has lost satellite signals. Check
antenna connections or try moving to a location with a clear view of
the sky.
NMEA Depth Is Below Transducer
—you must enter an
appropriate Keel Offset for the transducer (
page 43
).