Garmin Sport PRO Owner s Manual - Page 8
Using the Light, Handheld Device Specifications, Dog Collar Device Specifications, Sport PRO Battery - e collar
View all Garmin Sport PRO manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
mode by enabling it from the handheld device (Enabling the BarkLimiter Feature from the Handheld Device, page 3). Hold CONTINUOUS, TONE, or VIBE for 4 seconds. The dog collar device returns to training mode. Enabling the Independent BarkLimiter Feature from the Dog Collar Device The dog collar device can operate independently as a bark correction device. You can enable the BarkLimiter feature in auto-rise mode directly from the dog collar device. This provides longer battery life than enabling the BarkLimiter feature from the handheld device. NOTE: When using the device in this mode, the radio signal is disabled and you cannot control the dog collar device with the handheld device. 1 On the dog collar device, hold the power key until the LED flashes blue. 2 To return to training mode, turn off the dog collar device and turn it back on in training mode (Turning On the Dog Collar Device, page 2). Bark Odometer™ When you turn off the dog collar device in independent BarkLimiter mode, the LED flashes red and green to report the number of times the device detected a bark since it was last turned on. This can help you track your dog's barking behavior. Red flash Green flash 10 barks 1 bark For example, one red flash followed by four green flashes indicates the device detected 14 barks. Zero flashes indicates the device detected zero barks. Storage temperature range (up to 1 mo.) Storage temperature range (up to 3 mo.) Water rating From -20° to 50°C (from -4° to 122°F) From -20° to 35°C (from -4° to 95°F) 1 ATM* *The device withstands pressure equivalent to a depth of 10 m. For more information, go to www.garmin.com/waterrating. Sport PRO Battery Replacement Instructions WARNING This product contains a lithium-ion battery. To prevent the possibility of personal injury or product damage caused by battery exposure to extreme heat, store the device out of direct sunlight. Do not use a sharp object to remove batteries. CAUTION Contact your local waste disposal department to properly recycle the batteries. Sport PRO Handheld Device Components Using the Light You can use the light feature on your device to verify pairing, help locate your dog, and provide safety for your dog at night. 1 Select a dog collar device (Selecting a Dog Collar Device, page 2). 2 Set the dial to AUX. 3 Select to turn the light on. 4 Select to turn the light off. Device Information Handheld Device Specifications Battery type Battery life Operating temperature range Charging temperature range Storage temperature range (up to 1 mo.) Storage temperature range (up to 3 mo.) Water rating Rechargeable lithium-ion Up to 60 hr. of typical use From -20° to 60°C (from -4° to 140°F) From 0° to 40°C (from 32° to 104°F) From -20° to 50°C (from -4° to 122°F) From -20° to 35°C (from -4° to 95°F) IEC 60529 IPX7* *The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com /waterrating. Dog Collar Device Specifications Battery type Battery life Operating temperature range Charging temperature range Rechargeable, replaceable lithium-ion Up to 60 hr. of typical use From -20° to 60°C (from -4° to 140°F) From 0° to 40°C (from 32° to 104°F) Security screws À Back plate Á Battery  Battery connector à Front plate Ä Gasket Å Replacing the Handheld Device Battery Before you can replace the battery, you must remove all dirt, water, and debris from the device. You also need the security screwdriver included in the battery replacement kit. 1 Remove the security screws from the back of the device. 2 Lift up the back plate. 3 Grip the battery connector wires close to the connector, and pull the connector perpendicular to the circuit board to disconnect the battery connector from the device. 4 Remove the old battery from the back plate, noting the orientation of the battery. The battery fits tightly. It may be necessary to pry the battery out of the back plate using a non-sharp, non-metal object. 5 Install the new battery into the back plate with the label side up, using the same orientation as the old battery. 6 With the new battery, connect the battery connector to the device. When properly installed, the connector plug snaps into the port. 4 Device Information