Gateway 9210 Gateway 9210 Server User Guide - Page 77

BIOS, CD drive, Diskette drive

Get Gateway 9210 PDF manuals and user guides View all Gateway 9210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

BIOS The settings in the BIOS Setup utility are not retained ■ Replace the CMOS battery. For instructions, see "Replacing the CMOS battery" on page 49. CD drive Your server does not recognize a CD or the CD drive ■ Restart your server, then open the BIOS Setup utility by pressing and holding F2 while your server restarts. Make sure that the IDE controllers are enabled. For more information, see "Using the BIOS Setup Utility" on page 57. ■ Reinstall the device driver. For instructions, see "Using your System Companion CD" on page 20. ■ Turn off your server, then make sure the drive cables are connected correctly. For instructions, see "Installing a CD or diskette drive" on page 33. Your CD drive tray does not open ■ Press a straightened paper clip wire into the CD drive's manual eject hole. The drive tray opens. ■ If this problem happens frequently while the server is turned on, the drive may be defective. Diskette drive The diskette drive is not recognized ■ Restart your server. ■ Turn off your server, then make sure that the drive cables are connected correctly. For instructions, see "Installing a CD or diskette drive" on page 33. The diskette drive LED is lit continuously ■ Remove the diskette from the drive. If the light stays on, try restarting your server. ■ Turn off your server, then remove the combination drive and push it in again to make sure the drive is seated correctly. For instructions, see "Installing a CD or diskette drive" on page 33. 72 www.gateway.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
72
www.gateway.com
BIOS
The settings in the BIOS Setup utility are not retained
■
Replace the CMOS battery. For instructions, see
“Replacing the CMOS battery” on
page 49
.
CD drive
Your server does not recognize a CD or the CD drive
■
Restart your server, then open the BIOS Setup utility by pressing and holding
F2
while
your server restarts. Make sure that the IDE controllers are enabled. For more
information, see
“Using the BIOS Setup Utility” on page 57
.
■
Reinstall the device driver. For instructions, see
“Using your System Companion CD”
on page 20
.
■
Turn off your server, then make sure the drive cables are connected correctly. For
instructions, see
“Installing a CD or diskette drive” on page 33
.
Your CD drive tray does not open
■
Press a straightened paper clip wire into the CD drive’s manual eject hole. The drive
tray opens.
■
If this problem happens frequently while the server is turned on, the drive may be
defective.
Diskette drive
The diskette drive is not recognized
■
Restart your server.
■
Turn off your server, then make sure that the drive cables are connected correctly.
For instructions, see
“Installing a CD or diskette drive” on page 33
.
The diskette drive LED is lit continuously
■
Remove the diskette from the drive. If the light stays on, try restarting your server.
■
Turn off your server, then remove the combination drive and push it in again to make
sure the drive is seated correctly. For instructions, see
“Installing a CD or diskette drive”
on page 33
.