Home » GE Manuals » Home Security » GE 60-774 » Manual Viewer

GE 60-774 Installation Instructions - Page 1

GE 60-774 - Security SuperBus 2000 8-Zone Input Module Manual

UPC - 046188091768

Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

6XSHU%XVŠ = ,QSXW 0RGXOH ITI Part No. 60-774 Document Number: 466-1606 Rev. B November 2000 Product Summary 8557109A.DS4 VÌˆœ˜Ã Module Components Each SuperBus® 2000 8-Zone Input Module adds eight supervised hardwire zones. Each module includes mounting hardware and eight 2.0K ohm end-of-line (EOL) resistors. Power for the module is provided by the panel. Both normally open and normally closed detectors can be wired to module inputs. Using an EOL resistor on each loop input, the module monitors all zones and alerts the panel if there is an open/short circuit. Advent® panels can support multiple modules for up to 250 zone inputs. UltraGard® panels can support up to eight modules for 64 additional zone inputs. Concord™ panels can be expanded up to 76 zone inputs. For additional security, the plastic case includes space for installing a magnet and reed switch that can provide tamper protection to detect cover removal. SuperBus 2000 vs. SuperBus SuperBus 2000 panels have the ability to auto-address module unit numbers. When the panel is powered up, the panel automatically reads the unique SuperBus 2000 device ID number and assigns a unit number to the module. This eliminates manually setting DIP switches and the chance of identical unit number conflicts. SuperBus 2000 Panels R Advent R Concord (software versions 2.0 and later) SuperBus panels communicate with SuperBus 2000 modules but require the module unit number to first be set manually with DIP switches. SuperBus Panels R UltraGard R Concord (software versions 1.0-1.6) UNIT NUMBER DIP SWITCHES RED BUS STATUS LED GREEN POWER LED SUPERBUS 2000 DEVICE ID NUMBER LABEL SOFTWARE VERSION LABEL WIRING TERMINALS 9712G01A.DSF Figure 1. Module Circuit Board Components Table 1. Module Component Descriptions Component Function Unit Number DIP Used for manually setting unit Switches numbers (SuperBus panels). SuperBus 2000 Identifies unique device ID Device ID Number number (SuperBus 2000 Label panels). Software Version Label Identifies the installed software version. Green POWER LED Indicates module power status. Red BUS LED Flashes to indicate normal communication to the panel bus. Wiring Terminals Used for power, bus, and hardwire zone input connections. 1

Section	Page
Product Summary	1
SuperBus 2000 vs. SuperBus	1
Module Components	1
Figure 1. Module Circuit Board Components	1
Table 1. Module Component Descriptions	1
Component	1
Function	1
Installation Guidelines	2
Table 2. Maximum Bus Devices Per Panel	2
Panel	2
Maximum Bus Devices	2
Table 3: Maximum Wire Lengths	2
Panel	2
Maximum Wire Length	2
Tools and Supplies Needed	2
Installation	2
Mounting the Module	2
To Mount the Module on a Wall	2
1. Remove the module cover and set it aside (Figure 2).	2
Figure 2. Removing the Cover	2
2. Place the back-plate on the wall and mark the three mounting holes (Figure 3).	2
3. Drill holes and insert appropriate anchors.	2
4. Secure the back-plate to the wall with included screws.	2
Figure 3. Wall Mounting Hole Locations	3
To Mount the Module in an Advent Cabinet	3
1. Remove AC panel power and disconnect the backup battery(s).	3
2. Remove the module cover and set it aside (Figure 2).	3
3. Turn the module upside down and line up the holes on the back-plate at the desired location (F...	3
4. Secure the back-plate to the cabinet using three 1/4 - inch #6-32 self-tapping screws (not inc...	3
Figure 4. Mounting the Module in an Advent Cabinet	3
To Mount the Module in a Concord Cabinet	3
1. Remove AC panel power and disconnect the backup battery.	3
2. Remove and discard the module cover (Figure 2).	3
3. Insert a support standoff shown in Figure 5 (supplied with panel) into the panel circuit board.	3
Figure 5. Support Standoff	3
4. Slide the module back-plate onto the two clips located on the top-left corner or center of the...	3
5. Push the lower-right corner of the module onto the support standoff (see detail in Figure 6).	3
6. Gently press the module up and onto the cabinet side tab.	3
Figure 6. Mounting the Module in a Concord Cabinet	3
Wiring the Module	4
To Wire the Module to a Panel	4
1. Make sure the panel AC power is turned off or removed, and the panel backup battery(s) are dis...	4
2. Wire the module to the panel as shown in Figure 7 and explained in Table 4.	4
Figure 7. General Module Wiring	4
Table 4. SuperBus Module/Panel Wiring	4
Module	4
Terminals	4
Advent*	4
Ultra-	4
Gard	4
Concord	4
To Wire Detectors to the Module	4
Table 5. Zone Input Wire Runs	4
Gauge	4
Max. Wire Run*	4
1. Figure 8 shows an example of how to connect up to eight normally closed (N/C) or normally open...	4
Figure 8. Connecting N/C and N/O Intrusion Circuits to the Module	4
Installing a Cover Tamper Switch	5
To install the tamper reed switch (Figure 9):	5
1. Slide the reed switch into the reed switch holder located on the module back-plate shown in Fi...	5
2. Insert the magnet into the nibs on the module cover. Remove the magnet clip from the module ba...	5
3. Connect the normally closed reed switch (in series with a 2.0K ohm EOL resistor) to the module...	5
Figure 9. Installing the Reed Switch	5
Setting the Module Unit Numbers	5
On Concord (software versions 1.0–1.6) and UltraGard Panels	5
Figure 10. Module Unit Number DIP Switch Settings (Non-SuperBus 2000 panels)	5
On Concord (software versions 2.0 or later) and Advent Panels	5
Power Up and Bus Communication	6
On Concord and Advent Panels	6
New Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Both the green and red LEDs will turn on for one second. The green POWER LED will remain on an...	6
Existing Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Press 8 for System Menu.	6
4. Press 0 for Program Menu.	6
5. Enter your Install Code (default 0123).	6
6. Enter Item Number 48001 to add SuperBus devices. All installed devices are automatically added...	6
7. Press * twice to return to the Main Menu.	6
8. Both the green and red LEDs turn on for one second. The green POWER LED will remain on and the...	6
On UltraGard Panels	6
1. Verify that all wiring between the panel and module is correct.	6
2. Verify nonconflicting bus device unit number settings.	6
3. Connect the panel backup battery and restore panel AC power.	6
4. Turn on the panel AC power.	6
5. Set the UltraGard panel RUN/PROGRAM switch to PROGRAM.	6
Programming and Testing	7
Troubleshooting	7
Table 6. Troubleshooting	7
Problem	7
Action/Solution	7
1. Check for incorrect wiring connections.	7
2. Make sure panel AC power is applied and the backup battery(s) are connected.	7
3. If the LED still remains off, replace the module.	7
1. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
2. Check for incorrect wiring connections.	7
3. For Concord (software versions 1.0–1.6) and UltraGard panels make sure that module DIP switch ...	7
4. If the LED still doesn’t flash, replace the module.	7
1. For Concord (software versions 1.0–1.6) or UltraGard systems, check for bus devices with the s...	7
2. Re-initialize the panel by disconnecting and reconnecting panel power.	7
3. Make sure the zone has been “learned” into panel memory.	7
4. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
5. Remove zones and try installing the module without the zones.	7
6. Replace the module.	7
Specifications	7

Match case Limit results 1 per page

6XSHU%XV

²³´´´

µ=²,QSXW²0RGXOH

ITI Part No. 60-774

Document Number: 466-1606 Rev. B

November 2000

Product Summary

Each SuperBus

2000 8-Zone Input Module adds eight

supervised hardwire zones. Each module includes mounting

hardware and eight 2.0K ohm end-of-line (EOL) resistors.

Power for the module is provided by the panel.

Both normally open and normally closed detectors can be

wired to module inputs. Using an EOL resistor on each loop

input, the module monitors all zones and alerts the panel if

there is an open/short circuit.

Advent

panels can support multiple modules for up to 250

zone inputs. UltraGard

panels can support up to eight

modules for 64 additional zone inputs. Concord

™

panels can

be expanded up to 76 zone inputs.

For additional security, the plastic case includes space for

installing a magnet and reed switch that can provide tamper

protection to detect cover removal.

SuperBus 2000

vs.

SuperBus

SuperBus 2000 panels have the ability to auto-address mod-

ule unit numbers. When the panel is powered up, the panel

automatically reads the unique SuperBus 2000 device ID

number and assigns a unit number to the module. This elim-

inates manually setting DIP switches and the chance of

identical unit number conflicts.

SuperBus 2000 Panels

Advent

Concord (software versions 2.0 and later)

SuperBus panels communicate with SuperBus 2000 mod-

ules but require the module unit number to first be set man-

ually with DIP switches.

SuperBus Panels

UltraGard

Concord (software versions 1.0–1.6)

Module Components

Figure 1.

Module Circuit Board Components

Table 1. Module Component Descriptions

Component

Function

Unit Number DIP

Switches

Used for manually setting unit

numbers (SuperBus panels).

SuperBus 2000

Device ID Number

Label

Identifies unique device ID

number (SuperBus 2000

panels).

Software Version

Label

Identifies the installed

software version.

Green POWER

LED

Indicates module power status.

Red BUS LED

Flashes to indicate normal

communication to the panel

bus.

Wiring Terminals

Used for power, bus, and

hardwire zone input

connections.

SOFTWARE

VERSION LABEL

GREEN POWER

LED

UNIT NUMBER

DIP SWITCHES

WIRING

TERMINALS

9712G01A.DSF

RED BUS

STATUS LED

SUPERBUS 2000

DEVICE ID

NUMBER LABEL

8557109A.DS4