Home » GE Manuals » Home Security » GE 60-774 » Manual Viewer

GE 60-774 Installation Instructions - Page 6

Power Up and, Bus Communication

UPC - 046188091768

Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Power Up and Bus Communication Power Up and Bus Communication On Concord and Advent Panels This section describes how to power up the panel and module for both new and existing installations. New Installations 1. Verify that all wiring between the panel and module is correct. 2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays should come on. 3. Both the green and red LEDs will turn on for one second. The green POWER LED will remain on and the red BUS LED should flash to indicate successful communication with the panel. œÌi If the green POWER LED is not on or the red BUS LED does not flash, remove AC panel power, disconnect the backup battery(s), and see Table 6 "Troubleshooting." Existing Installations Concord Panels- Same as new installation. Advent Panels- 1. Verify that all wiring between the panel and module is correct. 2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays should come on. 3. Press 8 for System Menu. 4. Press 0 for Program Menu. 5. Enter your Install Code (default 0123). 6. Enter Item Number 48001 to add SuperBus devices. All installed devices are automatically added (learned) into panel memory when Devices Added is indicated. 7. Press * twice to return to the Main Menu. 8. Both the green and red LEDs turn on for one second. The green POWER LED will remain on and the red BUS LED should flash to indicate successful communication with the panel. œÌi If the green POWER LED is not on or the red BUS LED does not flash, remove AC panel power, disconnect the backup battery(s), and see Table 6 "Troubleshooting." On UltraGard Panels 1. Verify that all wiring between the panel and module is correct. 2. Verify nonconflicting bus device unit number settings. 3. Connect the panel backup battery and restore panel AC power. 4. Turn on the panel AC power. 5. Set the UltraGard panel RUN/PROGRAM switch to PROGRAM. If the alphanumeric touchpad displays 1-OFF and the 1 is flashing, you must enter the 4-digit installer code to place the panel into program mode. Alphanumeric touchpads should display PROGRAM MODE and the red BUS LED on the module should be flashing continuously, indicating successful communication with the panel. œÌi If the green POWER LED is not on or the red BUS LED does not flash, set the RUN/PROGRAM switch (UltraGard) to RUN, remove AC panel power, disconnect the backup battery, and see Table 6 "Troubleshooting." 6

Section	Page
Product Summary	1
SuperBus 2000 vs. SuperBus	1
Module Components	1
Figure 1. Module Circuit Board Components	1
Table 1. Module Component Descriptions	1
Component	1
Function	1
Installation Guidelines	2
Table 2. Maximum Bus Devices Per Panel	2
Panel	2
Maximum Bus Devices	2
Table 3: Maximum Wire Lengths	2
Panel	2
Maximum Wire Length	2
Tools and Supplies Needed	2
Installation	2
Mounting the Module	2
To Mount the Module on a Wall	2
1. Remove the module cover and set it aside (Figure 2).	2
Figure 2. Removing the Cover	2
2. Place the back-plate on the wall and mark the three mounting holes (Figure 3).	2
3. Drill holes and insert appropriate anchors.	2
4. Secure the back-plate to the wall with included screws.	2
Figure 3. Wall Mounting Hole Locations	3
To Mount the Module in an Advent Cabinet	3
1. Remove AC panel power and disconnect the backup battery(s).	3
2. Remove the module cover and set it aside (Figure 2).	3
3. Turn the module upside down and line up the holes on the back-plate at the desired location (F...	3
4. Secure the back-plate to the cabinet using three 1/4 - inch #6-32 self-tapping screws (not inc...	3
Figure 4. Mounting the Module in an Advent Cabinet	3
To Mount the Module in a Concord Cabinet	3
1. Remove AC panel power and disconnect the backup battery.	3
2. Remove and discard the module cover (Figure 2).	3
3. Insert a support standoff shown in Figure 5 (supplied with panel) into the panel circuit board.	3
Figure 5. Support Standoff	3
4. Slide the module back-plate onto the two clips located on the top-left corner or center of the...	3
5. Push the lower-right corner of the module onto the support standoff (see detail in Figure 6).	3
6. Gently press the module up and onto the cabinet side tab.	3
Figure 6. Mounting the Module in a Concord Cabinet	3
Wiring the Module	4
To Wire the Module to a Panel	4
1. Make sure the panel AC power is turned off or removed, and the panel backup battery(s) are dis...	4
2. Wire the module to the panel as shown in Figure 7 and explained in Table 4.	4
Figure 7. General Module Wiring	4
Table 4. SuperBus Module/Panel Wiring	4
Module	4
Terminals	4
Advent*	4
Ultra-	4
Gard	4
Concord	4
To Wire Detectors to the Module	4
Table 5. Zone Input Wire Runs	4
Gauge	4
Max. Wire Run*	4
1. Figure 8 shows an example of how to connect up to eight normally closed (N/C) or normally open...	4
Figure 8. Connecting N/C and N/O Intrusion Circuits to the Module	4
Installing a Cover Tamper Switch	5
To install the tamper reed switch (Figure 9):	5
1. Slide the reed switch into the reed switch holder located on the module back-plate shown in Fi...	5
2. Insert the magnet into the nibs on the module cover. Remove the magnet clip from the module ba...	5
3. Connect the normally closed reed switch (in series with a 2.0K ohm EOL resistor) to the module...	5
Figure 9. Installing the Reed Switch	5
Setting the Module Unit Numbers	5
On Concord (software versions 1.0–1.6) and UltraGard Panels	5
Figure 10. Module Unit Number DIP Switch Settings (Non-SuperBus 2000 panels)	5
On Concord (software versions 2.0 or later) and Advent Panels	5
Power Up and Bus Communication	6
On Concord and Advent Panels	6
New Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Both the green and red LEDs will turn on for one second. The green POWER LED will remain on an...	6
Existing Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Press 8 for System Menu.	6
4. Press 0 for Program Menu.	6
5. Enter your Install Code (default 0123).	6
6. Enter Item Number 48001 to add SuperBus devices. All installed devices are automatically added...	6
7. Press * twice to return to the Main Menu.	6
8. Both the green and red LEDs turn on for one second. The green POWER LED will remain on and the...	6
On UltraGard Panels	6
1. Verify that all wiring between the panel and module is correct.	6
2. Verify nonconflicting bus device unit number settings.	6
3. Connect the panel backup battery and restore panel AC power.	6
4. Turn on the panel AC power.	6
5. Set the UltraGard panel RUN/PROGRAM switch to PROGRAM.	6
Programming and Testing	7
Troubleshooting	7
Table 6. Troubleshooting	7
Problem	7
Action/Solution	7
1. Check for incorrect wiring connections.	7
2. Make sure panel AC power is applied and the backup battery(s) are connected.	7
3. If the LED still remains off, replace the module.	7
1. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
2. Check for incorrect wiring connections.	7
3. For Concord (software versions 1.0–1.6) and UltraGard panels make sure that module DIP switch ...	7
4. If the LED still doesn’t flash, replace the module.	7
1. For Concord (software versions 1.0–1.6) or UltraGard systems, check for bus devices with the s...	7
2. Re-initialize the panel by disconnecting and reconnecting panel power.	7
3. Make sure the zone has been “learned” into panel memory.	7
4. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
5. Remove zones and try installing the module without the zones.	7
6. Replace the module.	7
Specifications	7

Match case Limit results 1 per page

Power Up and Bus Communication

Power Up and

Bus Communication

On Concord and Advent Panels

This section describes how to power up the panel and mod-

ule for both new and existing installations.

New Installations

Verify that all wiring between the panel and module is

correct.

Connect the panel backup battery(s) and restore panel

AC power. Alphanumeric touchpad displays should

come on.

Both the green and red LEDs will turn on for one sec-

ond. The green POWER LED will remain on and the

red BUS LED should flash to indicate successful com-

munication with the panel.

If the green POWER LED is not on or the red BUS

LED does not flash, remove AC panel power, discon-

nect the backup battery(s), and see Table 6 “Trouble-

shooting.”

Existing Installations

Concord Panels–

Same as new installation.

Advent Panels–

Verify that all wiring between the panel and module is

correct.

Connect the panel backup battery(s) and restore panel

AC power. Alphanumeric touchpad displays should

come on.

Press

for

System Menu

Press

for

Program Menu.

Enter your

Install Code

(default

0123

Enter

Item Number

48001

to add SuperBus devices.

All installed devices are automatically added (learned)

into panel memory when

Devices Added

is indicated.

Press

twice to return to the Main Menu.

Both the green and red LEDs turn on for one second.

The green POWER LED will remain on and the red

BUS LED should flash to indicate successful commu-

nication with the panel.

If the green POWER LED is not on or the red BUS

LED does not flash, remove AC panel power, discon-

nect the backup battery(s), and see Table 6 “Trouble-

shooting.”

On UltraGard Panels

Verify that all wiring between the panel and module is

correct.

Verify nonconflicting bus device unit number settings.

Connect the panel backup battery and restore panel AC

power.

Turn on the panel AC power.

Set the UltraGard panel RUN/PROGRAM switch to

PROGRAM.

If the alphanumeric touchpad displays

1-OFF

and the

is flashing, you must enter the 4-digit installer code to

place the panel into program mode.

Alphanumeric touchpads should display

PROGRAM

MODE

and the red BUS LED on the module should be

flashing continuously, indicating successful communi-

cation with the panel.

If the green POWER LED is not on or the red BUS

LED does not flash, set the RUN/PROGRAM switch

(UltraGard) to RUN, remove AC panel power, discon-

nect the backup battery, and see Table 6 “Trouble-

shooting.”