Home » GE Manuals » Home Security » GE 60-774 » Manual Viewer

GE 60-774 Installation Instructions - Page 2

Installation Guidelines, Tools and Supplies Needed, Installation - security

UPC - 046188091768

Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Installation Guidelines Installation Guidelines R For the maximum number of bus devices and touchpads per panel see Table 2. Table 2. Maximum Bus Devices Per Panel Panel Maximum Bus Devices Advent 62 UltraGard 8 Concord 16 R Do not exceed the total panel output power when using panel power for bus devices and hardwired sensors that require it (see specific panel Installation Instructions). R Maximum current draw of each SuperBus 2000 8Z Input Module is 35 mA. R Do not exceed the maximum wire length from the panel to the module (see Table 3). Table 3: Maximum Wire Lengths Panel Maximum Wire Length Advent 22 ga. 1,800 ft./18 ga. 4000 ft. UltraGard 22 ga. 500 ft./18 ga. 1000 ft. Concord 22 ga. 1,800 ft./ 18 ga. 4,500 ft. R When using self or remotely powered devices with an Advent panel, do not exceed the maximum recommended wire length of 4000 feet using 22-gauge or larger wire. R Terminate each hardwired zone with a 2.0K ohm EOL resistor. For normally open circuits, wire the resistor in parallel. For normally closed circuits, wire the resistor in series. R Always install the EOL resistor at the last sensor or device on the circuit, not at the zone input terminals. Tools and Supplies Needed R Screwdrivers R Drill with bits R 3/8 -inch #6-32 self-tapping screws (included) R 2.0K ohm EOL resistors (49-467) (included) R 22-gauge or larger wire (18-gauge or larger for com- mercial applications) R 1/4-inch press-fit reed switch and magnet (not included) for cover tamper R 1/4-inch #6-32 self tapping screws (not included) for Advent cabinet mounting R Support standoff (included with Concord cabinet) Installation The module can be mounted R On a wall. R Inside an Advent cabinet. R Inside a Concord cabinet. R Inside a SuperBus module cabinet (60-698). Refer to the cabinet Installation Instructions for installation procedures. œÌi For UltraGard installations, the module must be mounted to a wall. The module will not fit in the UltraGard cabinet. Mounting the Module ÁIG"42 To prevent damaging the panel or module, remove the panel AC power and disconnect the backup battery(s) before installation. ÁIG"42 You must be free of all static electricity when handling electronic components. Touch a bare metal surface before touching the circuit board. To Mount the Module on a Wall 1. Remove the module cover and set it aside (Figure 2). PRESS DOWN HERE AND PULL AWAY FROM BASE 8557G47B.DS4 Figure 2. Removing the Cover 2. Place the back-plate on the wall and mark the three mounting holes (Figure 3). 3. Drill holes and insert appropriate anchors. 4. Secure the back-plate to the wall with included screws. 2

Section	Page
Product Summary	1
SuperBus 2000 vs. SuperBus	1
Module Components	1
Figure 1. Module Circuit Board Components	1
Table 1. Module Component Descriptions	1
Component	1
Function	1
Installation Guidelines	2
Table 2. Maximum Bus Devices Per Panel	2
Panel	2
Maximum Bus Devices	2
Table 3: Maximum Wire Lengths	2
Panel	2
Maximum Wire Length	2
Tools and Supplies Needed	2
Installation	2
Mounting the Module	2
To Mount the Module on a Wall	2
1. Remove the module cover and set it aside (Figure 2).	2
Figure 2. Removing the Cover	2
2. Place the back-plate on the wall and mark the three mounting holes (Figure 3).	2
3. Drill holes and insert appropriate anchors.	2
4. Secure the back-plate to the wall with included screws.	2
Figure 3. Wall Mounting Hole Locations	3
To Mount the Module in an Advent Cabinet	3
1. Remove AC panel power and disconnect the backup battery(s).	3
2. Remove the module cover and set it aside (Figure 2).	3
3. Turn the module upside down and line up the holes on the back-plate at the desired location (F...	3
4. Secure the back-plate to the cabinet using three 1/4 - inch #6-32 self-tapping screws (not inc...	3
Figure 4. Mounting the Module in an Advent Cabinet	3
To Mount the Module in a Concord Cabinet	3
1. Remove AC panel power and disconnect the backup battery.	3
2. Remove and discard the module cover (Figure 2).	3
3. Insert a support standoff shown in Figure 5 (supplied with panel) into the panel circuit board.	3
Figure 5. Support Standoff	3
4. Slide the module back-plate onto the two clips located on the top-left corner or center of the...	3
5. Push the lower-right corner of the module onto the support standoff (see detail in Figure 6).	3
6. Gently press the module up and onto the cabinet side tab.	3
Figure 6. Mounting the Module in a Concord Cabinet	3
Wiring the Module	4
To Wire the Module to a Panel	4
1. Make sure the panel AC power is turned off or removed, and the panel backup battery(s) are dis...	4
2. Wire the module to the panel as shown in Figure 7 and explained in Table 4.	4
Figure 7. General Module Wiring	4
Table 4. SuperBus Module/Panel Wiring	4
Module	4
Terminals	4
Advent*	4
Ultra-	4
Gard	4
Concord	4
To Wire Detectors to the Module	4
Table 5. Zone Input Wire Runs	4
Gauge	4
Max. Wire Run*	4
1. Figure 8 shows an example of how to connect up to eight normally closed (N/C) or normally open...	4
Figure 8. Connecting N/C and N/O Intrusion Circuits to the Module	4
Installing a Cover Tamper Switch	5
To install the tamper reed switch (Figure 9):	5
1. Slide the reed switch into the reed switch holder located on the module back-plate shown in Fi...	5
2. Insert the magnet into the nibs on the module cover. Remove the magnet clip from the module ba...	5
3. Connect the normally closed reed switch (in series with a 2.0K ohm EOL resistor) to the module...	5
Figure 9. Installing the Reed Switch	5
Setting the Module Unit Numbers	5
On Concord (software versions 1.0–1.6) and UltraGard Panels	5
Figure 10. Module Unit Number DIP Switch Settings (Non-SuperBus 2000 panels)	5
On Concord (software versions 2.0 or later) and Advent Panels	5
Power Up and Bus Communication	6
On Concord and Advent Panels	6
New Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Both the green and red LEDs will turn on for one second. The green POWER LED will remain on an...	6
Existing Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Press 8 for System Menu.	6
4. Press 0 for Program Menu.	6
5. Enter your Install Code (default 0123).	6
6. Enter Item Number 48001 to add SuperBus devices. All installed devices are automatically added...	6
7. Press * twice to return to the Main Menu.	6
8. Both the green and red LEDs turn on for one second. The green POWER LED will remain on and the...	6
On UltraGard Panels	6
1. Verify that all wiring between the panel and module is correct.	6
2. Verify nonconflicting bus device unit number settings.	6
3. Connect the panel backup battery and restore panel AC power.	6
4. Turn on the panel AC power.	6
5. Set the UltraGard panel RUN/PROGRAM switch to PROGRAM.	6
Programming and Testing	7
Troubleshooting	7
Table 6. Troubleshooting	7
Problem	7
Action/Solution	7
1. Check for incorrect wiring connections.	7
2. Make sure panel AC power is applied and the backup battery(s) are connected.	7
3. If the LED still remains off, replace the module.	7
1. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
2. Check for incorrect wiring connections.	7
3. For Concord (software versions 1.0–1.6) and UltraGard panels make sure that module DIP switch ...	7
4. If the LED still doesn’t flash, replace the module.	7
1. For Concord (software versions 1.0–1.6) or UltraGard systems, check for bus devices with the s...	7
2. Re-initialize the panel by disconnecting and reconnecting panel power.	7
3. Make sure the zone has been “learned” into panel memory.	7
4. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
5. Remove zones and try installing the module without the zones.	7
6. Replace the module.	7
Specifications	7

Match case Limit results 1 per page

Installation Guidelines

For the maximum number of bus devices and touch-

pads per panel see Table 2.

Do not exceed the total panel output power when using

panel power for bus devices and hardwired sensors that

require it (see specific panel

Installation Instructions

Maximum current draw of each SuperBus 2000

Input Module is 35 mA.

Do not exceed the maximum wire length from the

panel to the module (see Table 3).

When using self or remotely powered devices with an

Advent panel, do not exceed the maximum recom-

mended wire length of 4000 feet using 22-gauge or

larger wire.

Terminate each hardwired zone with a 2.0K ohm EOL

resistor. For normally open circuits, wire the resistor in

parallel. For normally closed circuits, wire the resistor

in series.

Always install the EOL resistor at the last sensor or

device on the circuit, not at the zone input terminals.

Tools and Supplies Needed

Screwdrivers

Drill with bits

3/8 -inch #6-32 self-tapping screws (included)

2.0K ohm EOL resistors (49-467) (included)

22-gauge or larger wire (18-gauge or larger for com-

mercial applications)

1/4-inch press-fit reed switch and magnet (not

included) for cover tamper

1/4-inch #6-32 self tapping screws (not included) for

Advent cabinet mounting

Support standoff (included with Concord cabinet)

Installation

The module can be mounted

On a wall.

Inside an Advent cabinet.

Inside a Concord cabinet.

Inside a SuperBus module cabinet (60-698). Refer to

the cabinet

Installation Instructions

for installation

procedures.

For UltraGard installations, the module must be

mounted to a wall. The module will not fit in the

UltraGard cabinet.

Mounting the Module

To prevent damaging the panel or module, remove the

panel AC power and disconnect the backup battery(s)

before installation.

You must be free of all static electricity when handling

electronic components. Touch a bare metal surface

before touching the circuit board.

To Mount the Module on a Wall

Remove the module cover and set it aside

(Figure 2).

Figure 2.

Removing the Cover

Place the back-plate on the wall and mark the three

mounting holes (Figure 3).

Drill holes and insert appropriate anchors.

Secure the back-plate to the wall with included screws.

Table 2. Maximum Bus Devices Per Panel

Panel

Maximum Bus

Devices

Advent

UltraGard

Concord

Table 3: Maximum Wire Lengths

Panel

Maximum Wire Length

Advent

22 ga. 1,800 ft./18 ga. 4000 ft.

UltraGard

22 ga. 500 ft./18 ga. 1000 ft.

Concord

22 ga. 1,800 ft./ 18 ga. 4,500 ft.

PRESS DOWN

HERE AND PULL

AWAY FROM BASE

8557G47B.DS4