Home » GE Manuals » Home Security » GE 60-774 » Manual Viewer

GE 60-774 Installation Instructions - Page 3

To Mount the Module in an Advent Cabinet, To Mount the Module in a Concord, Cabinet - 11

UPC - 046188091768

Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

MOUNTING HOLES Installation To Mount the Module in a Concord Cabinet 1. Remove AC panel power and disconnect the backup battery. 2. Remove and discard the module cover (Figure 2). 3. Insert a support standoff shown in Figure 5 (supplied with panel) into the panel circuit board. SUPPORT STANDOFF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 MAGNET CLIP REED SWITCH HOLDER 9712G02A.DSF Figure 3. Wall Mounting Hole Locations To Mount the Module in an Advent Cabinet 1. Remove AC panel power and disconnect the backup battery(s). 2. Remove the module cover and set it aside (Figure 2). 3. Turn the module upside down and line up the holes on the back-plate at the desired location (Figure 4). 4. Secure the back-plate to the cabinet using three 1/4 inch #6-32 self-tapping screws (not included). PANEL END MODULE END 8573g64A.DSF Figure 5. Support Standoff 4. Slide the module back-plate onto the two clips located on the top-left corner or center of the cabinet (Figure 6). œÌi The two mounting clips in the top-right corner of the cabinet are designated for a receiver module, but if a receiver module is not being used, the mounting clips may be used for the 8 Zone Input Module. 5. Push the lower-right corner of the module onto the support standoff (see detail in Figure 6). 6. Gently press the module up and onto the cabinet side tab. USABLE MOUNTING CLIPS (6) PANEL CABINET (COVER NOT SHOWN) MOUNTED MODULE SIDE TAB MOUNT WITH SELF TAPPING SCREWS MOUNTED MODULE 9712G11A.DSF ROOM FOR 3RD MODULE Figure 4. Mounting the Module in an Advent Cabinet 9712G08A.DSF PANEL CABINET (COVER NOT SHOWN) DETAIL SUPPORT STANDOFF (Included with Concord panel accessory package) Figure 6. Mounting the Module in a Concord Cabinet 3

Section	Page
Product Summary	1
SuperBus 2000 vs. SuperBus	1
Module Components	1
Figure 1. Module Circuit Board Components	1
Table 1. Module Component Descriptions	1
Component	1
Function	1
Installation Guidelines	2
Table 2. Maximum Bus Devices Per Panel	2
Panel	2
Maximum Bus Devices	2
Table 3: Maximum Wire Lengths	2
Panel	2
Maximum Wire Length	2
Tools and Supplies Needed	2
Installation	2
Mounting the Module	2
To Mount the Module on a Wall	2
1. Remove the module cover and set it aside (Figure 2).	2
Figure 2. Removing the Cover	2
2. Place the back-plate on the wall and mark the three mounting holes (Figure 3).	2
3. Drill holes and insert appropriate anchors.	2
4. Secure the back-plate to the wall with included screws.	2
Figure 3. Wall Mounting Hole Locations	3
To Mount the Module in an Advent Cabinet	3
1. Remove AC panel power and disconnect the backup battery(s).	3
2. Remove the module cover and set it aside (Figure 2).	3
3. Turn the module upside down and line up the holes on the back-plate at the desired location (F...	3
4. Secure the back-plate to the cabinet using three 1/4 - inch #6-32 self-tapping screws (not inc...	3
Figure 4. Mounting the Module in an Advent Cabinet	3
To Mount the Module in a Concord Cabinet	3
1. Remove AC panel power and disconnect the backup battery.	3
2. Remove and discard the module cover (Figure 2).	3
3. Insert a support standoff shown in Figure 5 (supplied with panel) into the panel circuit board.	3
Figure 5. Support Standoff	3
4. Slide the module back-plate onto the two clips located on the top-left corner or center of the...	3
5. Push the lower-right corner of the module onto the support standoff (see detail in Figure 6).	3
6. Gently press the module up and onto the cabinet side tab.	3
Figure 6. Mounting the Module in a Concord Cabinet	3
Wiring the Module	4
To Wire the Module to a Panel	4
1. Make sure the panel AC power is turned off or removed, and the panel backup battery(s) are dis...	4
2. Wire the module to the panel as shown in Figure 7 and explained in Table 4.	4
Figure 7. General Module Wiring	4
Table 4. SuperBus Module/Panel Wiring	4
Module	4
Terminals	4
Advent*	4
Ultra-	4
Gard	4
Concord	4
To Wire Detectors to the Module	4
Table 5. Zone Input Wire Runs	4
Gauge	4
Max. Wire Run*	4
1. Figure 8 shows an example of how to connect up to eight normally closed (N/C) or normally open...	4
Figure 8. Connecting N/C and N/O Intrusion Circuits to the Module	4
Installing a Cover Tamper Switch	5
To install the tamper reed switch (Figure 9):	5
1. Slide the reed switch into the reed switch holder located on the module back-plate shown in Fi...	5
2. Insert the magnet into the nibs on the module cover. Remove the magnet clip from the module ba...	5
3. Connect the normally closed reed switch (in series with a 2.0K ohm EOL resistor) to the module...	5
Figure 9. Installing the Reed Switch	5
Setting the Module Unit Numbers	5
On Concord (software versions 1.0–1.6) and UltraGard Panels	5
Figure 10. Module Unit Number DIP Switch Settings (Non-SuperBus 2000 panels)	5
On Concord (software versions 2.0 or later) and Advent Panels	5
Power Up and Bus Communication	6
On Concord and Advent Panels	6
New Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Both the green and red LEDs will turn on for one second. The green POWER LED will remain on an...	6
Existing Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Press 8 for System Menu.	6
4. Press 0 for Program Menu.	6
5. Enter your Install Code (default 0123).	6
6. Enter Item Number 48001 to add SuperBus devices. All installed devices are automatically added...	6
7. Press * twice to return to the Main Menu.	6
8. Both the green and red LEDs turn on for one second. The green POWER LED will remain on and the...	6
On UltraGard Panels	6
1. Verify that all wiring between the panel and module is correct.	6
2. Verify nonconflicting bus device unit number settings.	6
3. Connect the panel backup battery and restore panel AC power.	6
4. Turn on the panel AC power.	6
5. Set the UltraGard panel RUN/PROGRAM switch to PROGRAM.	6
Programming and Testing	7
Troubleshooting	7
Table 6. Troubleshooting	7
Problem	7
Action/Solution	7
1. Check for incorrect wiring connections.	7
2. Make sure panel AC power is applied and the backup battery(s) are connected.	7
3. If the LED still remains off, replace the module.	7
1. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
2. Check for incorrect wiring connections.	7
3. For Concord (software versions 1.0–1.6) and UltraGard panels make sure that module DIP switch ...	7
4. If the LED still doesn’t flash, replace the module.	7
1. For Concord (software versions 1.0–1.6) or UltraGard systems, check for bus devices with the s...	7
2. Re-initialize the panel by disconnecting and reconnecting panel power.	7
3. Make sure the zone has been “learned” into panel memory.	7
4. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
5. Remove zones and try installing the module without the zones.	7
6. Replace the module.	7
Specifications	7

Match case Limit results 1 per page

Installation

Figure 3.

Wall Mounting Hole Locations

To Mount the Module in an Advent Cabinet

Remove AC panel power and disconnect the backup

battery(s).

Remove the module cover and set it aside (Figure 2).

Turn the module upside down and line up the holes on

the back-plate at the desired location (Figure 4).

Secure the back-plate to the cabinet using three 1/4 -

inch #6-32 self-tapping screws (not included).

Figure 4.

Mounting the Module in an Advent Cabinet

To Mount the Module in a Concord

Cabinet

Remove AC panel power and disconnect the backup

battery.

Remove and discard the module cover (Figure 2).

Insert a support standoff shown in Figure 5 (supplied

with panel) into the panel circuit board.

Figure 5.

Support Standoff

Slide the module back-plate onto the two clips located

on the top-left corner or center of the cabinet

(Figure 6).

The two mounting clips in the top-right corner of the

cabinet are designated for a receiver module, but if a

receiver module is not being used, the mounting clips

may be used for the 8 Zone Input Module.

Push the lower-right corner of the module onto the sup-

port standoff (see detail in Figure 6).

Gently press the module up and onto the cabinet side

tab.

Figure 6.

Mounting the Module in a Concord Cabinet

9712G02A.DSF

MOUNTING HOLES

REED SWITCH

HOLDER

9 10 11 12 13 14 15 16

MAGNET

CLIP

9712G11A.DSF

PANEL CABINET

(COVER NOT SHOWN)

MOUNTED MODULE

ROOM FOR 3RD

MODULE

MOUNT WITH

SELF TAPPING

SCREWS

SUPPORT STANDOFF

8573g64A.DSF

PANEL

END

MODULE

END

9712G08A.DSF

USABLE MOUNTING

CLIPS (6)

MOUNTED

MODULE

PANEL CABINET

(COVER NOT SHOWN)

DETAIL

SUPPORT STANDOFF

(Included with Concord

panel accessory package)

SIDE TAB