Home » GE Manuals » Home Security » GE ATP 1000 » Manual Viewer

GE ATP 1000 Installation Instructions - Page 6

Specifications, Notices - interlogix

UPC - 782136711486

Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Specifications Notices learned by the panel, continue with step 6. 6. Force the panel to scan bus devices as follows: For systems where this is the only installed touchpad, remove panel AC and battery power, then re-apply power. For systems with more than one touchpad, go to another system touchpad and enter 8 + installer/dealer CODE (default = 4321) + 0 + 1. The display shows SCANNING BUS DEVICES, then a time and date display. The touchpad and all other bus devices should operate correctly and any bus failures should be cleared. Note If the panel still indicates a bus failure the panel may have previously learned a unit number that is no longer used by any bus device. See the specific panel Installation Instructions for more information on deleting unused unit numbers. Compatibility Concord, Concord Express, Concord Ultra Power Requirements 12 VDC nominal (See Table 1 for additional power requirements.) Temperature Range 32°F (0°C) to 120°F (49°C) Maximum Humidity 95% relative, non-condensing Dimensions 5.0" x 4.50" x 0.75" (L x W x D) UL Listings (all applied for): .....UL 985 Household Fire Warning System Units UL 1023 Household Burglar-Alarm System Units UL 1610 Central Station Burglar-Alarm Units (Commercial Burglary) Note See specific panel Installation Instructions for complete UL installation requirements for the system you are installing. FCC Part 15 Information to the User Changes or modifications not expressly approved by GE Interlogix can void the user's authority to operate the equipment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‰ Reorient or relocate the receiving antenna. ‰ Increase the separation between the equipment and receiver. ‰ Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits. ‰ Consult the dealer or an experienced radio/TV technician for help. ) ©2003 GE Interlogix. Concord is a trademark of GE Interlogix. All other names are trademarks of their owners. All rights reserved. *( ,QWHUORJL[ !!%%ÃTrp‚qÃT‡…rr‡ÃI‚…‡uÃ I‚…‡uÃThv‡ÃQhˆyÃHIÃ$$ (Ã VT6ÃÉÃ8hhqh UrpuvphyÃT 6 ATP1000 Touchpad/Display Installation Instructions

Section	Page
ATP1000 Touchpad/Display	1
Product Summary	1
Tools and Equipment Needed	1
Installation	1
Guidelines	1
Table 1: Touchpad Power Usage	1
Table 2: Maximum Touchpad Wire Lengths	1
Installing the Mounting Plate	2
1. Separate the mounting plate from the touchpad by first loosening the screw, then lift the touchpad away from the mounting plate (see Figure 1).	2
Figure 1. Separating the Touchpad from the Mounting Plate	2
2. For wall mounting, place the mounting plate on the wall and mark the mounting holes (see Figure 2). Be sure to leave a 3-inch clearance below for the touchpad door to open.	2
Figure 2. Mounting Hole Locations	2
3. Insert anchors into the wall at the marked locations where studs are not present.	2
4. Align the mounting plate holes with the wall or gang box screw holes and secure the back plate using the screws provided.	2
Note Do not overtighten screws or the mounting plate may bind and prevent the touchpad from mounting properly.	2
5. For wall-mount installations, cut a hole in the wall in the wire access area of the mount ing plate to pull the wiring cable through.	2
Wiring the Touchpad to the Panel	2
1. Remove panel AC and backup battery power.	2
2. Run a 4-conductor, 18- to 22-gauge wire from the panel to the touchpad location (see Table 2).	2
3. Connect the touchpad +12V, BUS A, BUS B, and GND terminals to the matching panel terminals (see Figure 3 for touchpad terminal identification).	2
Figure 3. Touchpad Wiring Connections	2
Attaching the Touchpad to the Mounting Plate	2
Power Up and Bus Communication	3
1. Verify that all wiring between the panel and touchpad is correct.	3
2. Connect the panel battery and restore AC power. Alphanumeric touchpads briefly show SCANNING BUS DEVICES, then display date and time.	3
Note Steps 3 through 9 are optional.	3
3. At the touchpad, enter program mode by pressing 8 + installer/dealer code (default = 4321) + 0 + 0. The touchpad should display SYSTEM PROGRAMMING.	3
4. Press É and the display shows SECURITY.	3
5. Press A or B until the display shows ACCESSORY MODULES, then press É. The display should read BUS DEVICES.	3
6. Press É. The display shows the lowest device address and its ID. The following example shows what a device address display may look like: UNIT - ID 0-02110185* *The 8-digit SuperBus ID number is also located on a label on back of the touchpad.	3
7. Press A or B to cycle through all bus device addresses until the touchpad appears.	3
8. After verifying the touchpad device ID, press Ç repeatedly until the display shows SYSTEM PROGRAMMING.	3
9. Press A or B until the display shows EXIT PROGRAMMING READY, then press É. The touchpad should show the date and time display.	3
Programming	3
Connecting the Touchpad for System Programming Only	3
To connect a programming touchpad to a Concord Express, Concord, or Concord Ultra panel with software version 2.0 or later:	3
1. With the panel powered up, connect the cable to the Programming Touchpad Header (see Fig ure 4).	3
Figure 4. Connecting a Programming Touchpad-Concord Express Shown, Concord Similar	3
2. Activate the touchpad by pressing 8 + code + 0 + 2.	3
3. Enter program mode by pressing 8 + installer/dealer code + 0 + 0 and program the panel using the panel Installation Instructions.	4
4. When programming is completed, simply disconnect the programming touchpad.	4
To connect a programming touchpad to a Concord panel with software versions 1.0-1.6:	4
1. Disconnect AC and backup battery power.	4
2. Connect the cable plug onto the panel Programming Touchpad Header pins (see Figure 5).	4
3. Reconnect the AC and backup battery power. The touchpad briefly displays ***********, SCANNING BUS DEVICES, then shows a time and date display.	4
Removing the programming touchpad from Concord panels with software versions 1.0-1.6:	4
1. After programming is completed, return to the ACCESSORY MODULES menu, then press É. The display should read BUS DEVICES.	4
2. Press É. The display shows the lowest unit number and its device name.	4
3. Press A or B until the display shows the programming touchpad unit number.	4
4. Press d to delete the device and its unit number from panel memory. The display shows: UNIT - TYPE 14-NONE	4
5. Exit program mode and disconnect the programming cable from the panel header.	4
Testing	4
Adjusting Display Brightness and Contrast	4
To adjust display brightness:	4
1. Enter user programming mode by pressing 9 + user, partition, or system master code. The display shows SYSTEM MENU, then TIME AND DATE (Concord panels with software versions 1.0-1.6 display USER CODES.)	4
2. Press B until the display shows OPTIONS, then press É. The display shows DOWNLOAD ING ON/OFF (current setting).	4
3. Press B twice and the display shows TOUCHPAD BRIGHTNESS 2 (default setting).	4
4. Enter a setting from 0 (darkest background) to 3 (brightest background), then press É.	4
5. The display flashes the entered selection, then stops after pressing É and displays the new set ting and brightness level.	4
6. Exit user programming mode.	4
To adjust display contrast:	4
1. Enter configuration mode by pressing the d and 6 buttons together for at least two seconds. The display shows DA nnn.	4
2. Press and release the 1 and 2 buttons together repeatedly, until the desired contrast level is displayed.	4
3. Press Ç and the display briefly shows DONE, then shows the time and date.	4
Troubleshooting	5
Table 3: Troubleshooting	5
1. Check for correct wiring connections at touchpad and panel terminals.	5
2. Make sure panel battery is connected correctly and that the panel trans former is plugged in.	5
3. Make sure panel trans former is not plugged into an electrical outlet controlled by a switch. Relocate transformer to an unswitched outlet location, if necessary.	5
1. Check the touchpad dis play contrast setting. It may be set to 0 (no dis play).	5
1. Check for correct bus wiring connections (green and white wires) at touchpad and panel terminals.	5
2. Make sure touchpad unit number is set to a differ ent number than all other bus devices. If neces sary, change the touch pad unit number (see procedure on this page). (Concord panels with software versions 1.0- 1.6 only.)	5
Changing the Touchpad Unit Number (Concord Panels with Software Version 1.0-1.6 Only)	5
To change the touchpad unit number:	5
1. At the touchpad, press and hold the d and 6 buttons together for at least 2 seconds. The dis play should show DA n, where n is the current touchpad unit number (000 - 015).	5
2. Press É. The display shows ENTER _.	5
3. Enter the desired three digit unit number (000 - 015), then press É. The display shows DA n, where n is the new touchpad unit number.	5
4. Do not use unit number 15 in Concord RF systems.	5
5. Press Ç to exit from the configuration mode.	5
6. Force the panel to scan bus devices as follows:	6
Specifications	6
Notices	6
FCC Part 15 Information to the User	6
FCC Part 15 Class B	6

Match case Limit results 1 per page

ATP1000 Touchpad/Display Installation Instructions

learned by the panel, continue with step 6.

Force the panel to scan bus devices as follows:

For systems where this is the only installed touchpad, remove panel AC and battery power,

then re-apply power.

For systems with more than one touchpad, go to another system touchpad and enter

8 +

installer/dealer

CODE

(default = 4321) +

. The display shows

SCANNING BUS

DEVICES

then a time and date display.

The touchpad and all other bus devices should operate correctly and any bus failures should be

cleared.

Note

If the panel still indicates a bus failure the panel may have previously learned a unit number that is no

longer used by any bus device. See the specific panel Installation Instructions for more information on

deleting unused unit numbers.

Specifications

Compatibility:

...........................

Concord, Concord Express, Concord Ultra

Power Requirements:

................

12 VDC nominal (See Table 1 for additional power requirements.)

Temperature Range:

..................

32°F (0°C) to 120°F (49°C)

Maximum Humidity:

................

95% relative, non-condensing

Dimensions:

..............................

5.0” x 4.50” x 0.75” (L x W x D)

UL Listings (all applied for):

.....

UL 985 Household Fire Warning System Units

...................................................

UL 1023 Household Burglar-Alarm System Units

...................................................

UL 1610 Central Station Burglar-Alarm Units

(Commercial Burglary)

Note

See specific panel Installation Instructions for complete UL installation requirements for the system you

are installing.

Notices

FCC Part 15 Information to the User

Changes or modifications not expressly approved by GE Interlogix can void the user’s authority to operate the equipment.

FCC Part 15 Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits.

Consult the dealer or an experienced radio/TV technician for help.

)

*(±,QWHUORJL[

names are trademarks of their owners.