GE AZ41E09DAB Owners Manual - Page 3

controls, Zoneline. - motors

Get GE AZ41E09DAB PDF manuals and user guides View all GE AZ41E09DAB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

About the controls on your Zoneline. in HiGH =mmCOOL LOW _ FAN AUTO _ HEAT m GEAppliances.com ! TEIVlP FAN MODE SLEEP OPERATION TEMP CONTROL FAN,MODE& SLEEPOPERATION Controls Temp Control Thetemp control is usedto maintain the room temperature.The compressorwill cycleon and off to keepthe room at the same level of comfort. Pressthe • pad to raisethe temperature. Pressthe • pad to lower the temperature. NOTET: he displayshows the set temperature, not the room temperature. Sleep Pressto set the air conditionerto run for 8 hours before it automaticallyreturns to the previous setting. When in the cooling mode and the sleeptimer is set,the set temperature will automatically increase2°Fafter the second hour then :].°F each hour overthe next two hours.Also,the fan speedwill changeto low.When in the heating mode, the set temperature will decreasein the same manner. Tocancel the sleepmode, pressthe MODEpad or the SLEEPpad a second time. Fan, Mode and Operation Control FAN--Setsthe fan operationfor HIGH, LOWor AUTO speed.When set at AUTO, it automatically switchesbetween LOW and HIGHas room temperature changes. MODE--COOL--Forcooling FAN--Forfan-only operation HEAT--Forheating OPERATION--ON/STOP--Turtnhse unit on or off. Powerremains connectedto the Zoneline.The Freeze/HeatSentinel features still function if active.Seethe Freezer/HeaSt entinelsection on page 6. NOTET: hetemperaturedisplaywill flash to indicate a possibleunit malfunction.Set operation control to STOPand then restart the unit. If the flashing light reappears within 30 minutes, coil for service. Quick Heat Recovery Activateseach time the thermostat is switchedfrom STOPor COOLmode to HEATmode. Electricheaters are energizeduntilthe thermostat set point is reached.On heat pump models,the heat pump operationwill resumeat the next call for heat. About Vour Heat Pump (6100 Series only) Heat pumps can save money by removing heat from the outside air-even when the outside temperature is below freezing-and releasing that heat indoors. To get the best performance from your heat pump, don't change the room thermostat very often. Raising the heat setting 2-3 degrees will cause the Zoneline to use its electric heating elements in order to reach the new temperature setting quickly. There isa 3-minute minimum compressor run time at any setting to prevent short cycling. The indoor fan motor starts before the compressor and stops after the compressor cycles off. When the outdoor temperature is lower than 25°F, heat is provided by the electric heater in the air conditioner instead of by the heat pump. The electric heating elements use much more electricity than heat pumps and cost more to operate. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
About the
controls
on
your
Zoneline.
GEAppliances.com
in
HiGH
=mmCOOL
LOW
_
FAN
AUTO
_
HEAT
m
!
TEIVlP
FAN
MODE
SLEEP OPERATION
TEMPCONTROL FAN,MODE& SLEEPOPERATION
Controls
Temp
Control
Thetemp control is usedto maintain the room
temperature.The compressorwill cycleon
and off to keepthe room at the same level
of comfort.
Pressthe •
pad to raisethe temperature.
Pressthe •
pad to lower the temperature.
NOTE:
The displayshows the set temperature,
not the room temperature.
Sleep
Pressto setthe air conditionerto runfor 8 hours
before it automaticallyreturns to the previous
setting.
When in the cooling mode and the sleeptimer
is set,the set temperature will automatically
increase2°F after the second hour then :].°F
each hour overthe next two hours.Also,the
fan speedwill changeto low.When in the
heating mode, the set temperature will
decreasein the same manner.
Tocancel the sleepmode, pressthe
MODE
pad
or the
SLEEP
pad a second time.
Fan,
Mode and
Operation
Control
FAN--Sets
the fan operationfor
HIGH,
LOW
or
AUTO
speed.When setat
AUTO,
it automatically switchesbetween
LOW
and
HIGH
as room temperature changes.
MODE--COOL--Forcooling
FAN--For
fan-only operation
HEAT--For
heating
OPERATION--ON/STOP--Turns
the unit
on or off. Powerremains connectedto
the Zoneline.TheFreeze/HeatSentinel
features stillfunction if active.Seethe
Freezer/Heat
Sentinel
section on page 6.
NOTE:
Thetemperaturedisplaywillflash
toindicateapossibleunitmalfunction.Set
operation
control
to STOPand then restart
the unit. If the flashing light reappears within
30
minutes,
coil
for
service.
Quick Heat Recovery
Activateseach time the thermostat is switchedfrom
STOP
or COOLmodeto HEATmode.Electricheaters
are energizeduntilthe thermostat set point
is reached.On heat pump models,the heat pump
operationwill resumeat the next call for heat.
About
Vour Heat Pump
(6100
Series only)
Heat pumps can save money by removing heat
from the outside air-even when the outside
temperature is below freezing-and
releasing
that heat indoors.
To get the best performance from your heat pump,
don't change the room thermostat very often.
Raising the heat setting 2-3 degrees will cause
the Zoneline to use its electric heating elements in
order to reach the new temperature setting quickly.
There isa
3-minute
minimum compressor
run time at any setting to prevent short cycling.
The indoor fan motor starts before the compressor
and stops after the compressor cycles off.
When the outdoor temperature is lower than 25°F,
heat is provided by the electric heater in the air
conditioner instead of by the heat pump.
The electric heating elements use much
more electricity than heat pumps and cost
more to operate.
3