GE JGP637BEJBB Owners Manual - Page 20

Installing the Cooktop

Get GE JGP637BEJBB - 36inch Gas Cooktop PDF manuals and user guides View all GE JGP637BEJBB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installation Instructions C Installing the Cooktop C1 Provide Supply Adequate Gas This cooktop is designed to operate on natural gas at 4″ of water column pressure. It is shipped from the factory set for natural gas. The convertible pressure regulator supplied with the unit must be connected in series with the manifold of the cooktop and must remain in series with the supply line regardless of whether natural or L.P. gas is being used. FOR PROPER OPERATION, THE MAXIMUM INLET PRESSURE TO THE REGULATOR MUST BE NO MORE THAN 14″ OF WATER COLUMN PRESSURE. For checking the regulator, the inlet pressure must be at least 1″ (or 3.4 KPA) greater than the regulator output setting. If the regulator is set for 4″ of water column pressure, the inlet pressure must be at least 5″. If the regulator is set for 10″, the inlet pressure must be at least 11″. The gas supply line to the cooktop should be 1/2″ or 3/4″ pipe. C2 Locate the electrical outlet and the Gas Shut Off valve beneath the cabinet. NEVER REUSE OLD CONNECTORS WHEN INSTALLING THIS UNIT. Shut Off Valve Electrical Outlet 12" Below Countertop Install a manual shutoff valve in the gas line in an easily accessible location outside the cooktop. Be sure you know how and where to shut off the gas supply to the cooktop. Install the electrical outlet 12″ below the countertop. C3 Installing the Regulator NEVER REUSE OLD CONNECTORS WHEN INSTALLING THIS COOKTOP. WARNING: Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal injury. Always use new flexible connectors when installing a gas appliance. Screw a section of pipe onto each end of the pressure regulator. Pressure Regulator To reduce the likelihood of gas leaks, apply teflon tape or a thread compound approved for use with LP or natural gases to all threaded connections. C4 Install the regulator onto the burner box bottom Screw the regulator and pipe connection into the burner box bottom. Make sure the top of the regulator is facing toward the cabinet front, easily accessible through the cabinet doors. Pressure Regulator Shut Off Valve Electrical Outlet 12" Below Countertop 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
C1
C3
20
Installation Instructions
This cooktop is designed to operate on natural
gas at 4
″
of water column pressure. It is
shipped from the factory set for natural gas.
The convertible pressure regulator supplied
with the unit must be connected in series with
the manifold of the cooktop and must remain
in series with the supply line regardless of
whether natural or L.P. gas is being used.
FOR PROPER OPERATION, THE MAXIMUM
INLET PRESSURE TO THE REGULATOR
MUST BE NO MORE THAN 14
″
OF WATER
COLUMN PRESSURE. For checking the
regulator, the inlet pressure must be at least
1
″
(or 3.4 KPA) greater than the regulator
output setting. If the regulator is set for 4
″
of
water column pressure, the inlet pressure
must be at least 5
″
. If the regulator is set for
10
″
, the inlet pressure must be at least 11
″
.
The gas supply line to the cooktop should be
1/2
″
or 3/4
″
pipe.
Provide Adequate Gas
Supply
Installing the Regulator
WARNING: Never reuse old flexible
connectors. The use of old flexible
connectors can cause gas leaks and
personal injury. Always use new
flexible connectors when installing
a gas appliance.
Screw a section of pipe
onto each end of the
pressure regulator.
C4
Install the regulator onto
the burner box bottom
Pressure
Regulator
Shut Off
Valve
Electrical
Outlet
12" Below
Countertop
Screw the
regulator and
pipe connection
into the burner
box bottom.
Make sure the
top of the
regulator is
facing toward
the cabinet front,
easily accessible
through the
cabinet doors.
NEVER REUSE OLD CONNECTORS
WHEN INSTALLING THIS COOKTOP.
To reduce the likelihood of gas leaks, apply
teflon tape or a thread compound approved
for use with LP or natural gases to all
threaded connections.
Pressure
Regulator
Installing the Cooktop
C
C2
Locate the electrical outlet
and the Gas Shut Off valve
beneath the cabinet.
Shut Off
Valve
Electrical
Outlet
12" Below
Countertop
Install a manual shutoff valve in the gas line
in an easily accessible location outside the
cooktop. Be sure you know how and where to
shut off the gas supply to the cooktop. Install
the electrical outlet 12
″
below the countertop.
NEVER REUSE
OLD CONNECTORS
WHEN INSTALLING
THIS UNIT.