GE NX-108E User Manual - Page 14

OTHER KEYPAD FUNCTIONS, Setting the keypad tone, Change partition (optional), View alarm memory,

Get GE NX-108E - Security NetworX NX-4 System PDF manuals and user guides
UPC - 782136402414
View all GE NX-108E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

OTHER KEYPAD FUNCTIONS Setting the keypad tone Step 1 Press the [r] key. Step 2 Press the [0] key. Keypad is now in the "Adjust Tone" mode. Step 3 Pressing the [1] key will make the keypad sounder go to higher tones, pressing the [2] key will make the keypad sounder go to lower tones. Step 4 When the desired tone is reached, press the [#] key to set this tone and exit from the "Adjust Tone" mode. Change partition (optional) Step 1 Press the [r] key. Step 2 Press the [1] key. Step 3 Press a NUMBER key between 1 and 8 to change partitions momentarily. Step 4 If no other key is pressed, it will go back to its standard partition in ten seconds. Step 5 If another key is pressed, the system will remain in the new partition until no keys have been pressed for 60 seconds. View alarm memory Step 1 Press the [r] key. Step 2 Press the [3] key to display the zone(s) on the keypad that created the last alarm. Step 3 The ALARM MEMORY feature will flash those zones that created alarms and will light steady those zones that were bypassed during the last alarm. Test function (optional) If programmed, this function will perform a battery test, communicator test, and/or a siren test. Step 1 Press [r] [4] [4]. The test will be performed as programmed. Step 2 If the siren test is performed, enter a user code to silence the siren. No alarms will be sent and no reports will be sent unless a communicator test is performed, at which time a test signal will be sent. NX-108/116/124E User manual Page 14 10/11/05

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
OTHER KEYPAD FUNCTIONS
Setting the keypad tone
Step 1
Press the
[
r
]
key.
Step 2
Press the
[0]
key.
Keypad is now in the “Adjust Tone” mode.
Step 3
Pressing the [
1
] key will make the keypad sounder go to higher tones, pressing the [
2
] key will
make the keypad sounder go to lower tones.
Step 4
When the desired tone is reached, press the [
#
] key to set this tone and exit
from the “Adjust Tone” mode.
Change partition (optional)
Step 1
Press the
[
r
]
key.
Step 2
Press the
[1]
key.
Step 3
Press a NUMBER key between 1 and 8 to change partitions momentarily.
Step 4
If no other key is pressed, it will go back to its standard partition in ten seconds.
Step 5
If another key is pressed, the system will remain in the new partition until no keys have been
pressed for 60 seconds.
View alarm memory
Step 1
Press the
[
r
]
key.
Step 2
Press the
[3]
key to display the zone(s) on the keypad that created the last alarm.
Step 3
The
ALARM MEMORY
feature will flash those zones that created alarms and will light steady those
zones that were bypassed during the last alarm.
Test function (optional)
If programmed, this function will perform a battery test, communicator test, and/or a siren test.
Step 1
Press
[
r
] [4] [4]
.
The test will be performed as programmed.
Step 2
If the siren test is performed, enter a user code to silence the siren.
No alarms will be sent and no reports will be sent unless a communicator test is performed, at which time a
test signal will be sent.
NX-108/116/124E User manual
Page 14
10/11/05