GE NX-108E User Manual - Page 8

Emergency Activation Keys - security manual

Get GE NX-108E - Security NetworX NX-4 System PDF manuals and user guides
UPC - 782136402414
View all GE NX-108E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Zone Light The zone lights are "off" when everything is normal. A zone light will be "on" if the zone has been bypassed. If a zone light is "flashing", that zone is in alarm or has been faulted. If a zone light is "flashing" rapidly, it means that the zone is in a trouble condition. Trouble conditions are Tamper Hardware Low Battery Loss of supervision (A combination of Alarm/Fault and Tamper/Trouble will produce a rapid "flashing" light for a short period of time, followed by a slow "flashing" light.) EMERGENCY ACTIVATION KEYS NOTES: You must hold these keys for 2 seconds to activate these functions. Your system may not be programmed for these activation keys. You should press these keys only in an emergency situation that requires response by emergency personnel. If your system is programmed for these functions, the following reports can be sent. Fire Key - This key can activate the fire alarm when pressed for two seconds. If your system is connected to a monitoring center, an emergency report could be sent to that center. Auxiliary Emergency Key - This key can activate the auxiliary alarm when pressed for two seconds. If your system is connected to a monitoring center, an emergency report could be sent to that center. Police (Panic/Hold-Up) Key - This key can sound a local audible alarm when pressed for two seconds. If your system is connected to a monitoring center, an emergency report could be transmitted to that center. NOTE: Some Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center. Check with your installing company to determine how your security system will respond to the Panic/HoldUp activation. NX-108/116/124E User manual Page 8 10/11/05

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
Zone Light
The
zone lights
are “off” when everything is normal. A
zone light
will be “on” if the zone has been
bypassed. If a
zone light
is “flashing”, that zone is in alarm or has been faulted. If a
zone light
is
“flashing” rapidly, it means that the zone is in a trouble condition.
Trouble conditions are
Tamper
Hardware
Low Battery
Loss of supervision
(A combination of Alarm/Fault and Tamper/Trouble will produce a rapid “flashing” light for a short
period of time, followed by a slow “flashing” light.)
EMERGENCY ACTIVATION KEYS
NOTES
: You must hold these keys for 2 seconds to activate these functions. Your system may not be programmed
for these activation keys. You should press these keys only in an emergency situation that requires response by
emergency personnel.
If your system is programmed for these functions, the following reports can be sent.
Fire Key
– This key can activate the fire alarm when pressed for two seconds. If your system is connected to a
monitoring center, an emergency report could be sent to that center.
Auxiliary Emergency Key
– This key can activate the auxiliary alarm when pressed for two seconds. If your system
is connected to a monitoring center, an emergency report could be sent to that center.
Police (Panic/Hold-Up) Key
- This key can sound a local audible alarm when pressed for two seconds. If your
system is connected to a monitoring center, an emergency report could be transmitted to that center. NOTE: Some
Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring
center. Check with your installing company to determine how your security system will respond to the Panic/Hold-
Up activation.
NX-108/116/124E User manual
Page 8
10/11/05