Gigabyte X570S AORUS MASTER User Manual - Page 49

Cpu Vdd18/cpu Vddp/dram Voltage Ch A/b/ddrvpp Voltage Ch A/b/dram

Get Gigabyte X570S AORUS MASTER PDF manuals and user guides View all Gigabyte X570S AORUS MASTER manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

ƒƒ Advanced Memory Settings ƒƒ Memory Subtimings dd Standard Timing Control/Advanced Timing Control/CAD Bus Setup Timing/ CAD Bus Drive Strength/Data Bus Configuration These sections provide memory timing settings. The respective timing setting screens are configurable only when Memory Timing Mode is set to Manual. Note: Your system may become unstable or fail to boot after you make changes on the memory timings. If this occurs, please reset the board to default values by loading optimized defaults or clearing the CMOS values. ƒƒ SPD Info Displays information on the installed memory. && Power Down Enable Enables or disables Power Down support. (Default: Auto) && CPU Vcore/Dynamic Vcore(DVID)/VCORE SOC/Dynamic VCORE SOC(DVID)/ CPU VDD18/CPU VDDP/DRAM Voltage (CH A/B)/DDRVPP Voltage (CH A/B)/DRAM Termination (CH A/B)/VDDP Voltage Conrol (Note)/VDDG Voltage Control (Note) These items allow you to adjust the CPU Vcore and memory voltages. ƒƒ CPU/VRM Settings This submenu allows you to configure Load-Line Calibration level, over-voltage protection level, overcurrent protection level, and PWM phases. (Note) This item is present only when you install a CPU that supports this feature. - 49 - BIOS Setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
BIOS Setup
- 49 -
±
Advanced Memory Settings
±
Memory Subtimings
d
Standard Timing Control/Advanced Timing Control/CAD Bus Setup Timing/
CAD Bus Drive Strength/Data Bus Configuration
These sections provide memory timing settings. The respective timing setting screens are configurable
only when
Memory Timing Mode
is set to
Manual
. Note: Your system may become unstable or fail to
boot after you make changes on the memory timings. If this occurs, please reset the board to default
values by loading optimized defaults or clearing the CMOS values.
±
SPD Info
Displays information on the installed memory.
&
Power Down Enable
Enables or disables Power Down support. (Default: Auto)
&
CPU Vcore/Dynamic Vcore(DVID)/VCORE SOC/Dynamic VCORE SOC(DVID)/
CPU VDD18/CPU VDDP/DRAM Voltage (CH A/B)/DDRVPP Voltage (CH A/B)/DRAM
Termination (CH A/B)/VDDP Voltage Conrol
(Note)
/VDDG Voltage Control
(Note)
These items allow you to adjust the CPU Vcore and memory voltages.
±
CPU/VRM Settings
This submenu allows you to configure Load-Line Calibration level, over-voltage protection level, over-
current protection level, and PWM phases.
(Note)
This item is present only when you install a CPU that supports this feature.