Haier DWL3225SDSS Product Manual - Page 10

Water, Drain

Get Haier DWL3225SDSS PDF manuals and user guides View all Haier DWL3225SDSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

English Water You must have • A hot water line with 20-120 psi (138-862 kPa) water pressure. • Inlet water temperature 120º F(49º C) minimum at the dishwasher is recommended. • 3/8" (0.9cm) O.D. tubing with compression fitting or flexible stainless steel braided fill line (1/2" (1.3cm) minimum plastic tubing is optional but not recommended). • A 90º elbow with 3/8" (0.9cm) N.P.T. external pipe threads on one end. Do not solder within 6"(15.2cm) from water inlet valve. DRAIN You must have • Use the new drain hose supplied with your dishwasher. If this is not suitable, use a new drain hose with a maximum length of 12 feet (3.7m) that meets all current AHAM / IAPMO test standards, is resistant to heat and detergent, and fits the drain connector on your dishwasher. • Have a high drain loop 30 inches (76.2cm) above the subfloor or floor. • Connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20 inches (50.8cm) minimum above the floor. • Use an air gap in the drain line if the drain hose is connected to house plumbing lower than 20 inches (50.8cm) above subfloor or floor. • Use 1/2" (1.3cm) minimum I.D. drain line fittings. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
9
English
YOU MUST HAVE
• A hot water line with 20-120 psi (138-862 kPa) water pressure.
• Inlet water temperature 120º F(49º C) minimum at the dishwasher is
recommended.
•
3/8
” (0.9cm) O.D. tubing with compression fitting or flexible stainless steel
braided fill line (
1/2
” (1.3cm) minimum plastic tubing is optional but not
recommended).
• A 90º elbow with
3/8
” (0.9cm) N.P.T. external pipe threads
on one end. Do not solder within 6”(15.2cm) from water inlet
valve.
WATER
YOU MUST HAVE
• Use the new drain hose supplied
with your dishwasher. If this is not
suitable, use a new drain hose
with a maximum length of 12
feet (3.7m) that meets all current
AHAM / IAPMO test standards,
is resistant to heat and detergent,
and fits the drain connector on
your dishwasher.
• Have a high drain loop 30 inches
(76.2cm) above the subfloor or
floor.
• Connect drain hose to waste tee
or disposer inlet above drain trap
in house plumbing and 20 inches
(50.8cm) minimum above the floor.
• Use an air gap in the drain line if the drain hose is connected to house
plumbing lower than 20 inches (50.8cm) above subfloor or floor.
• Use
1/2
” (1.3cm) minimum I.D. drain line fittings.
DRAIN