Haier DWL3225SDSS Product Manual - Page 17

Helpful Tip

Get Haier DWL3225SDSS PDF manuals and user guides View all Haier DWL3225SDSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

English HELPFUL TIP: Put cardboard under dishwasher until it is installed. The cardboard will help protect floor during installation. 4. Remove terminal box cover "H". Pull appliance wires "I" through hole in terminal box. Do not untie the knot in the wires. If you are direct wiring: install a UL-listed/ CSA-certified clamp connector "J" to the terminal box. If using conduit use a UL-listed/CSA certified conduit connector. If you are installing a power supply cord kit, do so now and follow kit instructions. 5. Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed "K" (you need the lowest point). Check chart for that height opening. Put wheels "L" in the required position. Turn both front leveler legs to the same height. I K Min Cutout Height 34" (86.4 cm) 34 1/4" (87 cm) 34 1/2" (87.6 cm) Wheel Position (See Illustration) 1 2 3 Number of Turns on Front Leg 10 5 0 If the minimum cutout height is less than 34" (86.4 cm), the adjustable legs can be removed for additional clearance. This will allow the dishwasher to fit into a 33 4/5" (85.9 cm) high cutout, but the dishwasher will be more difficult to move into position. If the wheels are removed, protect the floor when moving the dishwasher. H J K 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
English
16
4. Remove terminal box cover “H”. Pull
appliance wires “I” through hole in terminal
box. Do not untie the knot in the wires.
If you are direct wiring: install a UL-listed/
CSA-certified clamp connector “J” to
the terminal box.
If using conduit use a
UL-listed/CSA certified conduit connector. If
you are installing a power supply cord kit,
do so now and follow kit instructions.
5. Measure height of cabinet opening from
underside of countertop to floor where
dishwasher will be installed “K” (you
need the lowest point). Check chart for
that height opening. Put wheels “L” in the
required position. Turn both front leveler
legs to the same height.
If the minimum cutout height is less than
34” (86.4 cm), the adjustable legs can be
removed for additional clearance. This will
allow the dishwasher to fit into a 33 4/5”
(85.9 cm) high cutout, but the dishwasher
will be more difficult to move into position.
If the wheels are removed, protect the floor
when moving the dishwasher.
HELPFUL TIP:
Put cardboard under dishwasher until it is installed. The cardboard
will help protect floor during installation.
H
I
J
K
Min Cutout
Height
Wheel Position
(See Illustration)
Number of Turns
on Front Leg
34” (86.4 cm)
1
10
34 1/4” (87 cm)
2
5
34 1/2” (87.6 cm)
3
0