Haier HLC1700AXS User Manual - Page 10

Location Requirements, Unit Dimensions And Clearances

Get Haier HLC1700AXS PDF manuals and user guides View all Haier HLC1700AXS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

ENGLISH LOCATION REQUIREMENTS • The washer must be installed on a solid floor to minimize vibration during the spin cycle. • The floor should be level with maximum slope of 1" (25mm) under entire washer. • A suitable location is protected from direct sunlight and heat sources such as radiators, baseboard heaters, cooking appliances, etc. • Do not install on carpeting. • The location must have a grounded electrical outlet located within 4ft. (1.2m) of the power cord on the back of the washer. • Hot and cold water faucets must be present within 3ft. (0.9m) of the hot and cold connections on the washer. • A water heater must supply hot water with a temperature of at least 120ºF (49ºC). • The water pressure should be between 20-100 psi (138-690 kPa). • This appliance must be operated at room temperature. • Do not install or operate this appliance in an area where the ambient temperature can fall below freezing. UNIT DIMENSIONS AND CLEARANCES 40-23/32" 23-7/16" 22-15/32" Open Door 20" 33-9/32" Front View Side View Minimum Installation Clearances / Detergent Minimum Alcove Closet Front n/a 1" (25mm) Sides and Rear 1" (25mm) 1" (25mm) Top of Control 1" (25mm) 1" (25mm) Front ventilation openings are required for closet installations: 24 square inches-3inches from bottom. 48 square inches-3 inch from top. Louvered door with equivalent openings is acceptable. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
LOCATION REQUIREMENTS
•
The washer must be installed on a solid
flo
or to minimize vibration during the spin cycle.
•
The
floor
should be level with maximum slope of 1" (25mm) under entire washer.
•
A suitable location is protected from direct sunlight and heat sources such as
radiators, baseboard heaters, cooking appliances, etc.
•
Do not install on carpeting.
•
The location must have a grounded electrical outlet located within 4ft. (1.2m) of
the power cord on the back of the washer.
•
Hot and cold water faucets must be present within 3ft. (0.9m) of the hot and cold
connections on the washer.
•
A water heater must supply hot water with a temperature of at least 120ºF (49ºC).
•
The water pressure should be between 20-100 psi (138-690 kPa).
•
This appliance must be operated at room temperature.
•
Do not install or operate this appliance in an area where the ambient temperature
can fall below freezing.
UNIT DIMENSIONS AND CLEARANCES
23-7/16"
Front View
Side View
22-15/32"
40-23/32"
Open
Door 20"
33-9/32"
Minimum Installation Clearances / Detergent Minimum
Alcove
Closet
Front
n/a
1" (25mm)
Sides and Rear
1" (25mm)
1" (25mm)
1" (25mm)
1" (25mm)
Top of Control
ENGLISH
8
Front ventilation openings are required for closet installations:
24 square inches-3inches from bottom. 48 square inches-3 inch from top.
Louvered door with equivalent openings is acceptable.