Haier HWD1500 User Manual - Page 12

Connection of water inlet hose and, washing machine, Water Drainage Hose

Get Haier HWD1500 PDF manuals and user guides View all Haier HWD1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

English INSTALLATION Connection of water inlet hose and washing machine (use new hose sets, old hose sets should not be reused) • Connect the straight coupling of the inlet hose to the water tap and make sure to tighten it. • Connect the elbow coupling of the inlet hose to each inlet valves of the unit and make sure to tighten it. Note: • Please be sure that the COLD inlet hose is connected with the valve for cold water (marked with "C"). • Please be sure that the HOT inlet hose is connected with the valve for hot water (marked with "H"). H Water Inlet Hoses . Note: A flat rubber washer must be present inside each end of the inlet hoses. Over tightening may cause damage to the valve. 100cm 80cm Water Drainage Hose • The height of the pipe for the water drainage hose should be between 2'6" to 3'3". The water drain hose must be securely placed on the clip on the back of the washing machine. • Use the water drainage support (bracket) supplied as an accessory for proper installation. If the water drain hose needs to be extended, it should not be extended more than 8'2". (Longer extension will result in concurrent water inflow and outflow.) The diameter of the extension hose should be the same as the original hose. Caution: Water drainage hose must not be immersed in water. The original and extension hoses should be tightly connected. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
11
English
INSTALLATION
Connection of water inlet hose and
washing machine
(use new hose sets, old hose sets should not be reused)
•
Connect the straight coupling of the inlet hose
to the water tap and make sure to tighten it.
•
Connect the elbow coupling of the inlet hose
to each inlet valves of the unit and make sure
to tighten it.
Note:
•
Please be sure that the COLD inlet hose is
connected with the valve for cold water
(marked with "C").
•
Please be sure that the HOT inlet hose is
connected with the valve for hot water
(marked with "H").
Note:
A flat rubber washer must be present inside each end of the inlet hoses.
Over tightening may cause damage to the valve.
Water Drainage Hose
•
The height of the pipe for the water drainage
hose should be between 2'6" to 3'3". The
water drain hose must be securely placed
on the clip on the back of the washing machine.
•
Use the water drainage support (bracket)
supplied as an accessory for proper installation.
If the water drain hose needs to be extended,
it should not be extended more than 8'2".
(Longer extension will result in concurrent water
inflow and outflow.) The diameter of the extension
hose should be the same as the original hose.
Caution:
Water drainage hose must not be immersed in water. The original and
extension hoses should be tightly connected.
H
100cm
80cm
Water Inlet Hoses