Haier HWM60-78 User Manual - Page 3
Safety precautions, Trouble-shooting, Answer to question
View all Haier HWM60-78 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself. Phenomenan The digitron displays E0. The reason The top lid is opened during reserve procedure. How to settle Close the top lid. The drainage cannot work, or is too slow. Is the drain hose put down? The digitron displays E1. Is the drain hose blocked? It stops running in midway. The digitron The top lid is not closed. displays E2. The safety switch acts, and the spinning cannot work. The digitron displays E3. Are the laundries put slantingly? Is the machine slanting? The water filling does not work, or is Is the water tap opened, or is there water slow. After about 40 minutes later, supply failure? the digital displays E4. Is the water inlet valve blocked? Is the water pressure too low? Put down the drain hose. Open and close the top lid once. Clean the foreign material. Open and close The top Lid Once. Close the top lid. Reorder the laundries. Close the top lid. The machine will start running after 10 seconds of being placed horizontally. Open the water tap. Push the start/Pause button once. Clean the water inlet valve then push the start/Pause button once. Push the Start/Pause button once. The digitron displays E6. The water level sensor is bad. Please contact the after-sales service department. The digitron displays E8. The digitron displays E9. The machine does not act Not wash Not spin The power voltage is too low. The power voltage is too high. Is there power failure? Is the power plug inserted tightly? Is the water level reached preset position? Is the power plug inserted tightly? Is the top lid closed reliably? Are the laundries set flat? Pull off the power plug. Wait for the voltage resuming normal before usage. Please use it when there's power supply. Insert the power plug tightly. Fill water to the preset position. Insert the power plug tightly. Close the top lid. Set the laundries flat. There's abnormal sound inside the machine Is the machine slanting? Are the laundries put slantingly in spinning? Are there any foreign materials? Adjust the machine to be even Reorder the laundries and close the top lid. Remove the foreign materials. The water tap leaks Is the screw of the jointer of water inlet hose loose or awry? Fasten the screw of the jointer properly. Common phenomena Phenomena The spinning is intermittent when it starts. The wash procedure pauses. Select SPIN program, but it does not work. The pulsator pauses during washing,rinsing or adding water. There may be some water flowing out of the drain hose in the first use of the machine. When the power plug is inserted,the computer board indicator is switched on,and the machine starts working Explanation Balance the laundries to avoid slanting. The cloth sensor is detecting , it will add water after about 48 senconds The program is setting the drain time , A certain period is needed before it starts spinning. It is to avoid splashing during water filling. It is the water remained performance inspection by the factory. It is the special power resum efunction.In the cass of power failure or the power plug is loose during washin,the machine can save the running program,and resume the program after the power supply is recovered.You do not need to set the program again. Safety precautions Before Using Please plug the plug on special 220V AC receptacle. Be sure to use single-phase three pins receptacle.Ensure the earthing prong of the power receptacle is earthed reliably.Use leakage protector if possible. In normal usage of the washing machine, the power plug shall be ready to be pulled or plugged with hand. Be sure to pull the plug off and close the water faucet when occurring power failure,delivering the maching, setting the machine idle or cleaning the machine,Do not plug or pull the power plug with wet hand. Earth Do not bend, stretch, twist, bind the power cord by force, or reformit. Do not press or clamp it with heavy items. If the power cord and power plug are bad, or the receptacle is loose, be sure to have it replaced by the technicians of our special shop or our agent,or the after-sales service department to avoid any risk.Keep the prong of the power plug clean.If dust is found on the power plug, please wipe it off with dry cloth. In case the washing machine is installed on ground Do not use water with temperature higher than 50 with carpet, be careful not to block the ventilation hole with carpet. The ventilation holes at the bottom Soft items Do not put the machine at damp place like the bathroom. Never wash it with water. Do not put wet laundries on the control panel coating. Do not wash water-proof laundry like the raincoat, bikecovers, down textiles etc. To avoid abnormal vibrations in spinning and damages to the laundries. Do not let the machine share one receptacle with other electric appliances. If the power plug is damaged, or the plugging into the receptacle is loose, do not use the plug any more.