Before Using
Before Using
The drainage shall be smooth with the drain hose.
The height of the drain hose shall be less than 10cm,
or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.
Do not step on or press the drain hose.
If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra
hose shall
not less than 30mm, and the
length
shall not exceed
1.5m.
If the extra hose is too long,cut it either at A or
at B point.
A
B
<10cm
A
>
30mm
<1.5m
If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
Usage the drain hose
The washing machine away from wall should be overrun 20mm. The largest allowable slope of the shank base
of the machine is 1
.The slanting or rough ground will result inunstable running or stoppage of the machine.
Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
Adjust the Installation position
Fasten
Loosen
High
Low
the adjustable nut
the adjustable feet
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
2 . After adjustment, fasten the nut.
Using process
Using process
After switching on the power, the washing
machine will set
to common program including"wash, rinse,
spin "automatically.
To select other procedures,
push the "SOAK",
" WASH",
" RINSE"
or "SPIN"
button
to select the time of soak,
wash and spin,
and the times of rinse.
After switching on the power,
if you push one
of
the
button among
"wash",
"rinse"and"spin",
the digitron
of the former procedures
will turn off automatically. The former procedures will not run. For instance: after switching on the power.
If you push the "spin" button first, it will execute spin singly after starting.
Attention
.
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use
the
soak
program
for the
woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
The
pulsator
will not
rotate unless the
water is
filled to "3" water level.
The soak
procedure can work in cooperation with automatic
programs like standard, jeans,
chemical fiber and
cotton.There is intermittent pulsator stirring during soak.
After
the
machine starts
operation,
you can only set the program and procedure during washing,
and can not
make setting in other cases.
WATER
LEVEL
Press " WATER LEVEL "button,
select suitable water level
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically.
To select other water level,
first push the
"START/PAUSE"
button,
then push the
"WATER LEVEL"
button to set the water level. Refer to
"standard dosage
of
detergent and
water quantity"in Page 9 and "water level button"in Page 11 for selection.
Page 9
Page 11
Water Level and Time Table for Each Program (self programming not included)
Program
Water
level
Wash(min)
1~10
About
About 15
FIBRE
About 4
1~10
About 12
About 41
3
About 2
About 6
NORMAL
1~10
About 19-25
About 10-16
1~10
About 10
About 49
About 6
1~10
About 20
About 54
JEAN
Rinse twice, about 5 each time
About 3
1~10
About 3
About 24
1~10
About 5
About 3
About 30
Rinse(min/time)
Spin(minu)
Total time
(min)
About 4
Saving water program, total about 8 around
Saving water program, total about 4 around
Rinse twice, about 3 each time
Rinse three times, about 3 each time
Rinse twice, about 2 each time
Rinse twice, about 2 each time
QUICK
POSTHASTE
COTTON
WOOLLEN
SILK
Saving water program, total about 10 around
1
2
3
4
5
6
7
8
9
10
