HP 2000-2b30DX HP 2000 Notebook PC Compaq Presario CQ58 Notebook PC Compaq Pre - Page 42

Display subcomponents (bezel, webcam, panel)

Get HP 2000-2b30DX PDF manuals and user guides View all HP 2000-2b30DX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Display subcomponents (bezel, webcam, panel) This section describes removing display subcomponents that do not require that you remove the entire display assembly from the computer. You can remove the display bezel, webcam/microphone module, and display panel while the display assembly is still attached to the computer. To remove the remaining display subcomponents, including the hinge covers, hinges, cable, antennas, and enclosure, you must remove the entire display assembly from the computer. See Display assembly on page 71 for more information about removing the display assembly in its entirety. Description 35.6-cm (14.0-in), HD, LED, BrightView display panel 35.6-cm (14.0-in), HD, LED, Anti-glare display panel Display bezel (includes Mylar screw covers) HP TrueVision HD webcam/microphone module HP VGA webcam/microphone module Rubber display bumpers Spare part number 685101-001 694746-001 685081-001 694747-001 685112-001 685102-001 Before removing the display bezel, webcam/microphone module, and display panel while the display assembly is still attached to the computer, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 34). To remove the display bezel, webcam/microphone module, and display panel while the display assembly is still attached to the computer: 1. Position the computer right-side up with the front toward you, and then open it. 2. Remove the two Mylar screw covers (1) and the two Phillips PM2.5×4.0 screws (2) that secure the display bezel to the display assembly. The Mylar screw covers are included with the display bezel spare part kit. 3. Flex the inside edges of the top edge, the left and right sides, and the bottom edge of the display bezel until the bezel disengages from the display enclosure. Component replacement procedures 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Display subcomponents (bezel, webcam, panel)
This section describes removing display subcomponents that do not require that you remove the
entire display assembly from the computer. You can remove the display bezel, webcam/microphone
module, and display panel while the display assembly is still attached to the computer.
To remove the remaining display subcomponents, including the hinge covers, hinges, cable,
antennas, and enclosure, you must remove the entire display assembly from the computer. See
Display assembly
on page
71
for more information about removing the display assembly in its
entirety.
Description
Spare part number
35.6-cm
(14.0-in), HD, LED, BrightView display panel
685101-001
35.6-cm
(14.0-in), HD, LED, Anti-glare display panel
694746-001
Display bezel (includes Mylar screw covers)
685081-001
HP TrueVision HD webcam/microphone module
694747-001
HP VGA webcam/microphone module
685112-001
Rubber display bumpers
685102-001
Before removing the display bezel, webcam/microphone module, and display panel while the display
assembly is still attached to the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see
Battery
on page
34
).
To remove the display bezel, webcam/microphone module, and display panel while the display
assembly is still attached to the computer:
1.
Position the computer right-side up with the front toward you, and then open it.
2.
Remove the two Mylar screw covers
(1)
and the two Phillips PM2.5×4.0 screws
(2)
that secure
the display bezel to the display assembly. The Mylar screw covers are included with the display
bezel spare part kit.
3.
Flex the inside edges of the top edge, the left and right sides, and the bottom edge of the display
bezel until the bezel disengages from the display enclosure.
Component replacement procedures
35