HP 2000-2b30DX HP 2000 Notebook PC Compaq Presario CQ58 Notebook PC Compaq Pre - Page 79

Support the display assembly when removing the following screws. Failure

Get HP 2000-2b30DX PDF manuals and user guides View all HP 2000-2b30DX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

● USB board (see USB board on page 67) ● Power connector cable (see Power connector cable on page 69) To remove the display assembly in its entirety: 1. Disconnect the display panel cable (1) from the system board. 2. Release the wireless antenna cables from the clips (2) built into the base enclosure. NOTE: Models may have either one or two antennas installed. CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in damage to the display assembly and other computer components. 3. Remove the five Phillips PM2.5×6.0 screws (1) that secure the display assembly to the computer. 72 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
●
USB board (see
USB board
on page
67
)
●
Power connector cable (see
Power connector cable
on page
69
)
To remove the display assembly in its entirety:
1.
Disconnect the display panel cable
(1)
from the system board.
2.
Release the wireless antenna cables from the clips
(2)
built into the base enclosure.
NOTE:
Models may have either one or two antennas installed.
CAUTION:
Support the display assembly when removing the following screws. Failure to
support the display assembly can result in damage to the display assembly and other
computer components.
3.
Remove the five Phillips PM2.5×6.0 screws
(1)
that secure the display assembly to the
computer.
72
Chapter 4
Removal and replacement procedures