HP BL480c HP ProLiant BL480c Server Blade User Guide - Page 15

Remove the server blade, Remove the access panel

Get HP BL480c - ProLiant - 4 GB RAM PDF manuals and user guides
UPC - 882780759664
View all HP BL480c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

After initiating a virtual power down command, be sure that the server blade goes into standby mode by observing that the system power LED is amber. Remove the server blade 1. Identify the proper server blade. 2. Power down the server blade (on page 14). 3. Remove the server blade. 4. Place the server blade on a flat, level work surface. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly ground the server blade before beginning any installation procedure. Improper grounding can cause ESD. Remove the access panel To remove the component: 1. Power down the server blade (on page 14). 2. Remove the server blade (on page 15). 3. Lift the access panel latch and slide the access panel to the rear. 4. Remove the access panel. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly ground the server blade before beginning any installation procedure. Improper grounding can cause ESD. Operations 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Operations 15
After initiating a virtual power down command, be sure that the server blade goes into standby mode by
observing that the system power LED is amber.
Remove the server blade
1.
Identify the proper server blade.
2.
Power down the server blade (on page
14
).
3.
Remove the server blade.
4.
Place the server blade on a flat, level work surface.
WARNING:
To reduce the risk of personal injury from hot surfaces, allow the drives and
the internal system components to cool before touching them.
CAUTION:
To prevent damage to electrical components, properly ground the server blade before
beginning any installation procedure. Improper grounding can cause ESD.
Remove the access panel
To remove the component:
1.
Power down the server blade (on page
14
).
2.
Remove the server blade (on page
15
).
3.
Lift the access panel latch and slide the access panel to the rear.
4.
Remove the access panel.
WARNING:
To reduce the risk of personal injury from hot surfaces, allow the drives and
the internal system components to cool before touching them.
CAUTION:
To prevent damage to electrical components, properly ground the server blade before
beginning any installation procedure. Improper grounding can cause ESD.