HP Brio 81XX HP BRIO PC - Online Reference Guide, Not Orderable - Page 57

Installing the Drive

Get HP Brio 81XX PDF manuals and user guides View all HP Brio 81XX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

3 Upgrading and Adding Accessories Adding Accessories Installing the Drive 1 Remove the computer's cover (refer to "Removing the Cover" on page 37). 2 Install the new hard disk drive in the computer: • For a 3.5-inch hard disk drive - mount the new hard disk drive in the 3.5-inch bay (below the floppy disk drive). Have the connectors of the new hard disk drive pointing towards the back of the computer. • For a 5.25-inch hard disk drive - mount the new hard disk in the 5.25-inch bay. Have the connectors of the new hard disk drive pointing towards the back of the computer. 3 Secure the drive to the computer using the four screws provided with the drive. Two screws must be inserted in each side of the drive. Using screws other than those provided may cause damage to the device. 4 Connect the power and data cables to the rear of the drive. Both connectors are shaped to fit one way only. Use the second connector on the hard disk drive data cable. Refer to "System Board Connectors" on page 55 for an illustration of the cables and connectors. Data Cable Storage Device Power Cable 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
57
3
Upgrading and Adding Accessories
Adding Accessories
Installing the Drive
1
Remove the computer’s cover (refer to
“
Removing the Cover
” on page 37
).
2
Install the new hard disk drive in the computer:
•
For a 3.5-inch hard disk drive – mount the new hard disk drive in the 3.5-inch bay (below the floppy disk drive). Have
the connectors of the new hard disk drive pointing towards the back of the computer.
•
For a 5.25-inch hard disk drive – mount the new hard disk in the 5.25-inch bay. Have the connectors of the new hard
disk drive pointing towards the back of the computer.
3
Secure the drive to the computer using the four screws provided with the drive. Two screws must be inserted in each
side of the drive. Using screws other than those provided may cause damage to the device.
4
Connect the power and data cables to the rear of the drive. Both connectors are shaped to fit one way only. Use the
second connector on the hard disk drive data cable. Refer to
“
System Board Connectors
” on page 55
for an illustration
of the cables and connectors.
Power Cable
Data Cable
Storage Device