HP Brio 85xx hp brio 85xx, online reference guide - Page 60

If there are any errors reported during the computer's startup routine, press

Get HP Brio 85xx PDF manuals and user guides View all HP Brio 85xx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

3 Upgrading and Adding Accessories 5 Insert the drive into the shelf from the front of the computer. 6 Secure the device in position using the screws provided with it. Using screws other than those provided may cause damage to the device. 7 Connect the power and data cables to the rear of the device. The power connector and data connector are shaped to fit one way only. Refer to "System Board Connectors" on page 54 for more information about which connectors to use. 8 Install any other accessories before replacing the cover and reconnecting the power cords and any telecommunications cables. Replace the front bezel on the computer. 9 Turn on the display, and then turn on the computer. 10 In Windows, check that the drive has been recognized. To do this, double-click the My Computer icon on the desktop, the disk drives that are available on your computer are displayed in the My Computer window. 11 Depending on the type of drive you have installed, you may need to install some driver software. This could be done when you have returned to the operating system. If the new drive is not recognized, you may need to run the Setup program: restart the computer and press when Press to enter SETUP is displayed at the bottom of the screen. If you have any doubts about using the HP Setup program, contact your reseller for help. If the new drive is not recognized, check that you have correctly followed the installation procedure described above. If there are any errors reported during the computer's startup routine, press to view the error(s) and take any necessary action. If you have any doubts about using the HP Setup program, contact your reseller for help. If you cannot start your computer properly, remove the drive and try starting your computer again. If the computer now starts without any problems, there may be a problem with the new drive. If you experience any other problems as a result of the upgrade, and your computer is supplied with the HP Brio Center, refer to the support tools for further assistance.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
3
Upgrading and Adding Accessories
5
Insert the drive into the shelf from the front of the computer.
6
Secure the device in position using the screws provided with it. Using screws other than those provided may cause
damage to the device.
7
Connect the power and data cables to the rear of the device. The power connector and data connector are shaped to
fit one way only. Refer to
“
System Board Connectors
” on page 54
for more information about which connectors to use.
8
Install any other accessories before replacing the cover and reconnecting the power cords and any telecommunications
cables. Replace the front bezel on the computer.
9
Turn on the display, and then turn on the computer.
10
In Windows, check that the drive has been recognized. To do this, double-click the My Computer icon on the desktop,
the disk drives that are available on your computer are displayed in the My Computer window.
11
Depending on the type of drive you have installed, you may need to install some driver software. This could be done
when you have returned to the operating system.
If the new drive is not recognized, you may need to run the
Setup
program: restart the computer and press
when
Press <F2> to enter SETUP
is displayed at the bottom of the screen. If you have any doubts about using the HP
Setup
program, contact your reseller for help.
If the new drive is not recognized, check that you have correctly followed the installation procedure described above.
If there are any errors reported during the computer’s startup routine, press
to view the error(s) and take any
necessary action. If you have any doubts about using the HP
Setup
program, contact your reseller for help.
If you cannot start your computer properly, remove the drive and try starting your computer again. If the computer
now starts without any problems, there may be a problem with the new drive.
If you experience any other problems as a result of the upgrade, and your computer is supplied with the HP Brio Center,
refer to the support tools for further assistance.