HP DL165 Technologies for HP ProLiant 100-series G5 (Generation 5) servers, 2n - Page 13

ProLiant DL100-series servers ProLiant DL100-series servers use 1U or 2U rack-mountable chassis that are well-suited for mediumdensity environments. Table 5 lists key components of the DL100-series servers. Table 5. Key components of ProLiant DL100-series servers Form factor Processor support Chipset DL120 G5 1U 1 Intel Xeon, Core2, Pentium, or Celeron processor Intel 3200 DL160 G5 1U 2 Intel Xeon 5400 processors Intel 5400 Memory Max. memory Unbuffered PC2-6400 (DDR2-800) 8 GB Fully-buffered PC2-5300 (DDR2-667) 32 GB DL165 G5 1U 2 AMD Opteron 2300 processors DL180 G5 2U 2 Intel Xeon 5400 processors ServerWorks HT2100 & HT1000 Registered PC2-5300 (DDR2-667) 32 GB Intel 5100 Registered PC2-5300 (DDR2-667) 16 GB DL185 G5 2U 2 AMD Opteron 2200 processors ServerWorks HT2100 & HT1000 Registered PC2-5300 (DDR2-667) 32 GB Max. number of hard drives 2 3.5" SATA or SAS drives 4 3.5" SATA or SAS drives 4 3.5" SATA or SAS drives I/O slots: Standard Optional 1 PCIe x8 [1,5] 1 PCIe x4 [2,5] 2 PCIe x16 [1,6] 1 PCIe x16 [1,5] 1 PCIe x4 [2,5] 2 PCI-X 64-bit USB ports: Standard Optional 2 front, 2 rear 1 internal 2 front, 2 rear 1 internal 2 front, 2 rear, 1 internal Disk controller: Non-hot plug Hot-plug SATA controller [3] SAS HBA [4] SATA controller [3] SAS HBA [4] SATA controller [3] SAS HBA [4] Network adapter Embedded NC105i PCIe GbE adapters 2 embedded NC105i PCIe GbE adapters 1 embedded NC7782 PCI GbE adapters Management IPMI 2.0, SMASH CLP support, LO100i (standard) IPMI 2.0, SMASH CLP support, LO100i (standard) IPMI 2.0, SMASH CLP support, LO100i (standard) NOTES: [1] Full-length, full-height slot [2] Half-length, low-profile slot [3] Embedded on non-hot plug systems [4] PCIe card [5] x8 PCIe connector [6] One slot populated with SAS HBA on hot-plug configurations 12 3.5" SATA or SAS drives 2 PCIe x4 [1,5] 1 PCIe x8 [2,6] 2 PCI-X 64-bit 2 front, 2 rear 1 internal SATA controller [3] SAS HBA [4] 1 embedded NC7781 PCI GbE adapters IPMI 2.0, SMASH CLP support LO100c (optional) 14 3.5" SATA or SAS drives 2 PCIe x8 [1] 1 PCIe x4 [2,5,6] 2 PCI-X 64-bit 2 front, 2 rear 1 internal SATA controller [4] SAS HBA [4] NC326i dual-port PCIe GbE adapter IPMI 2.0, SMASH CLP support LO100i (standard) 13