HP Designjet 4200 HP Designjet 4200 Scanner - Assembly and Maintenance Poster - Page 3

caution - scanner

Get HP Designjet 4200 PDF manuals and user guides View all HP Designjet 4200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

11 12 13 Lock the keyboard assembly to the touch screen arm using one M4×8 screw. Lift the scanner into place, locating the rubber feet in the holes indicated, and fixing with the four special screws. Rest the touch screen face down on a table. Attach the touch screen bracket to the rear of the touch screen using two M4×8 screws as shown. 14 15 16 Attach with three more M4×8 screws as shown. Slide the hub of the touch screen assembly into the touch screen arm. Secure the hub of the touch screen bracket using an M3×8 screw. 17 18 Unfold the bin. Insert the left and right arms of the bin into the two slots on the rear of the legs. Make sure they are fully inserted. The unit is now assembled and should appear as in the above illustration. cleaning the scan area... You are now required to clean the scan area. To do so you will need the cleaning tools provided in the maintenance kit and a cleaning fluid (not included in the maintenance kit). Caution: do not use abrasives, acetone, benzene, or fluids that contain these chemicals. Do not spray liquids directly onto the scanner glass plate or anywhere else in the scanner. 19 20 21 E X 16 T 14 E E D N E T I X 4D L A M R O mm N E 6 8 10 12 2 L A M R N mm O 6D TE ID N E X 16 E T X E 2 4 14 12 10 8 0.55 0.63 0.39 0.47 E X EE T T I X E 0.31 D 0.24 0.16 0.08 Inches D N O N R M A L N Inches O R M A L 0.08 0.24 D 0.16 0.39 0.31 0.63 0.55 0.47 I T E X 16E14 1X2 1TE0X8E 64 INTD 2 E mm D NORMA L D E T E N E X T E N0E.6DX03.I5E05.T407.D309.301.204.N106.0O8 IRncMheAs L X E L A MmmR 2 O 4 N 6 8 10D12TEI14X1D6EN E T X E L AMRON Inches0D.080.E160.D24T0. I3N10.X3E90E.47T0.550X.63E 16E14 1X2 1TE0X8E I 6NT 4D2E mm D NORMA L E X T E N0E.6DX03.I5E05.T407.D309.301.204.N106.0O8 IRncMheAs L 16E14 1X2 1TE0X8E 64 INTD 2 E mm D NORMA L E X T E N0E.6DX03.I5E05.T407.D309.301.204.N106.0O8 IRncMheAs L L A MmmR 2 O 4 N 6 8 10D12TEI14X1D6EN E T X E L AMRON Inches0D.080.E160.D24T0. I3N10.X3E90E.47T0.550X.63E L A MmmR 2 O 4 N 6 8 10D12TEI14X1D6EN E T X E L AMRON Inches0D.080.E160.D24T0. I3N10.X3E90E.47T0.550X.63E Open the scanner cover to expose the scan area. 22 Position your fingers in the four lock slots (two at each end of the platen indicated by the green arrows above), and press down (blue arrows). With the platen pushed down, slide the two locks inwards until the pins at either end pop up, locking the platen open and ready to be removed. 23 caution: see note after step 18 24 16E14 1X2 1TE0X8E I 6NT 4D2E mm D NORMA L E X T E N0E.6DX03.I5E05.T407.D309.301.204.N106.0O8 IRncMheAs L L A MmmR 2 O 4 N 6 8 10D12TEI14X1D6EN E T X E L A M R O N Inches0D.080.E160.D24T0. I3N10.X3E90E.47T0.550X.63E Raise the two handles, and remove the pressure platen. Clean the glass with a lint-free cloth and a mild, streak-free, glass cleaner. 3 Dry the glass fully using a separate clean, dry lint-free cloth like the one provided with the maintenance kit.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
E
E
X
T
E
N
D
E
D
E
X
I
T
E
X
I
T
N
O
R
M
A
L
E
X
T
E
N
D
E
D
N
O
R
M
A
L
Inches
mm
0.63
0.55
0.47
0.39
0.31
0.24
0.16
0.08
16
14
12
10
8
6
4
2
E
X
T
E
N
D
E
D
E
X
I
T
E
X
I
T
N
O
R
M
A
L
E
X
T
E
N
D
E
D
N
O
R
M
A
L
Inches
mm
0.63
0.55
0.47
0.39
0.31
0.24
0.16
0.08
16
14
12
10
8
6
4
2
cleaning the scan area...
You are now required to clean the scan
area. To do so you will need the cleaning
tools provided in the maintenance kit and a
cleaning fluid (not included in the
maintenance kit).
Caution:
do not use abrasives, acetone,
benzene, or fluids that contain these
chemicals. Do not spray liquids directly
onto the scanner glass plate or anywhere
else in the scanner.
12
13
11
18
20
21
15
16
19
3
14
Lock the keyboard assembly to the touch screen
arm using one M4×8 screw.
Lift the scanner into place, locating the rubber
feet in the holes indicated, and fixing with the
four special screws.
Unfold the bin. Insert the left and right arms of
the bin into the two slots on the rear of the legs.
Make sure they are fully inserted.
Open the scanner cover to expose the scan
area.
Position your fingers in the four lock slots (two at
each end of the platen indicated by the green
arrows above), and press down (blue arrows).
With the platen pushed down, slide the two locks
inwards until the pins at either end pop up,
locking the platen open and ready to be removed.
caution:
see note after step 18
23
24
22
Dry the glass fully using a separate clean, dry
lint-free cloth like the one provided with the
maintenance kit.
The unit is now assembled and should appear
as in the above illustration.
Raise the two handles, and remove the pressure
platen.
Clean the glass with a lint-free cloth and a mild,
streak-free, glass cleaner.
17
Rest the touch screen face down on a table.
Attach the touch screen bracket to the rear of the
touch screen using two M4×8 screws as shown.
Attach with three more M4×8 screws as shown.
Slide the hub of the touch screen assembly into
the touch screen arm.
Secure the hub of the touch screen bracket using
an M3×8 screw.