HP ENVY m6-aq000 Maintenance and Service Guide - Page 62

Power connector cable, Remove the two Phillips PM2.5×4.5 screws

Get HP ENVY m6-aq000 PDF manuals and user guides View all HP ENVY m6-aq000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Power connector cable Description Power connector cable Spare part number 808155-011 Before removing the power connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 27), and then removed the following components: a. Battery (see Battery on page 29). b. Fan/heat sink assembly (see Fan/heat sink assembly on page 39). c. System board (see System board on page 43). Remove the power connector cable: 1. Remove the two Phillips PM2.5×4.5 screws (1) that secure the left display hinge to the keyboard/ top cover. 2. Release the left display hinge (2) by swinging it up and back. 3. Remove the power connector cable (3). Reverse this procedure to install the power connector cable. 54 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Power connector cable
Description
Spare part number
Power connector cable
808155-011
Before removing the power connector cable, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
27
), and then removed the following components:
a.
Battery (see
Battery
on page
29
).
b.
Fan/heat sink assembly (see
Fan/heat sink assembly
on page
39
).
c.
System board (see
System board
on page
43
).
Remove the power connector cable:
1.
Remove the two Phillips PM2.5×4.5 screws
(1)
that secure the left display hinge to the keyboard/
top cover.
2.
Release the left display hinge
(2)
by swinging it up and back.
3.
Remove the power connector cable
(3)
.
Reverse this procedure to install the power connector cable.
54
Chapter 5
Removal and replacement procedures