HP EVA P6000 HP Enterprise Virtual Array Updating Product Software Guide (xcs1 - Page 32

Verifying installation on the management server, Upgrading the management module

Get HP EVA P6000 PDF manuals and user guides View all HP EVA P6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

NOTE: The value for Required Disk Space shown in the Pre-Install Summary dialog represents the file size of files the installer will load; the size displayed in Add/Remove Programs is determined by Windows. 12. The installation summary window opens. Click Finish. All software components are installed in the directory :\Program Files\Hewlett-Packard Verifying installation on the management server To verify that the software was installed successfully: 1. Ensure that the software icons for HP P6000 Command View , HP Command View EVAPerf , and/or HP System Scripting Utility appear on the desktop. 2. Run HP P6000 Command View. 3. Verify the display of array resources in the interface. In the navigation pane, click Hardware and verify that: • New, uninitialized arrays appear as uninitialized arrays. • Previously initialized arrays appear with their previous names and correct status. (Select each storage array to view the Properties window.) • Previous disk groups, hosts, virtual disks, and other resources appear in the navigation pane. If the information is not displayed properly, you may need to configure your browser settings. See the HP P6000 Command View Installation Guide for more information. Upgrading the management module Estimated time to complete: 25 minutes When to perform: Anytime before the upgrade If you have an EVA4400, P6300 EVA or P6500 EVA, follow the procedures in this section to: • Upgrade HP P6000 Command View on the management module (for array-based management). • Upgrade the management module software. NOTE: Management module software is bundled with the array-based management version of HP P6000 Command View. Thus, when you upgrade HP P6000 Command View on the management module, you are also upgrading the management module software. Even if you are not using array-based management, you must complete the procedure in this section for the EVA4400, P6300 EVA, or P6500 EVA, to ensure that the array has the current management module software. To upgrade the management module: 1. Connect a server with a DVD drive to the management module port (1, Figure 8 (page 32)) on the controller enclosure. Figure 8 Management module 32 Preparing for the upgrade

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
NOTE:
The value for Required Disk Space shown in the Pre-Install Summary dialog represents
the file size of files the installer will load; the size displayed in Add/Remove Programs is
determined by Windows.
12.
The installation summary window opens. Click
Finish
.
All software components are installed in the directory
<system drive>
:\Program Files\Hewlett-Packard
Verifying installation on the management server
To verify that the software was installed successfully:
1.
Ensure that the software icons for HP P6000 Command View
, HP Command View EVAPerf
, and/or HP System Scripting Utility
appear on the desktop.
2.
Run HP P6000 Command View.
3.
Verify the display of array resources in the interface. In the navigation pane, click
Hardware
and verify that:
•
New, uninitialized arrays appear as uninitialized arrays.
•
Previously initialized arrays appear with their previous names and correct status. (Select
each storage array to view the Properties window.)
•
Previous disk groups, hosts, virtual disks, and other resources appear in the navigation
pane.
If the information is not displayed properly, you may need to configure your browser settings. See
the
HP P6000 Command View Installation Guide
for more information.
Upgrading the management module
Estimated time to complete:
25 minutes
When to perform:
Anytime before the upgrade
If you have an EVA4400, P6300 EVA or P6500 EVA, follow the procedures in this section to:
•
Upgrade HP P6000 Command View on the management module (for array-based
management).
•
Upgrade the management module software.
NOTE:
Management module software is bundled with the array-based management version of
HP P6000 Command View. Thus, when you upgrade HP P6000 Command View on the
management module, you are also upgrading the management module software.
Even if you are not using array-based management, you must complete the procedure in this section
for the EVA4400, P6300 EVA, or P6500 EVA, to ensure that the array has the current management
module software.
To upgrade the management module:
1.
Connect a server with a DVD drive to the management module port (1,
Figure 8 (page 32)
)
on the controller enclosure.
Figure 8 Management module
32
Preparing for the upgrade