HP EliteDesk 800 Hardware Reference Guide - Page 121

Installing the new optical drive, then connect the cable to the rear of the drive 2.

Get HP EliteDesk 800 PDF manuals and user guides View all HP EliteDesk 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Installing the new optical drive NOTE: If you are installing an optical drive in a bay that did not previously have a drive in it, you must remove the access panel, the front bezel, and the bezel blank covering the opening of the bay before proceeding. Follow the procedures in Removing the computer access panel on page 100 and Removing a bezel blank on page 103. 1. Follow the instructions for removing the optical drive if one was installed. Refer to Removing the optical drive on page 111. 2. Attach the release latch to the new optical drive. Refer to Preparing the new optical drive on page 112. 3. Slide the optical drive through the front bezel all the way into the bay so that it locks in place (1), then connect the cable to the rear of the drive (2). 4. Replace the computer access panel. 5. If the computer was on a stand, replace the stand. 6. Reconnect the power cord and turn on the computer. 7. Lock any security devices that were disengaged when the computer cover or access panel was removed. ENWW Replacing the optical drive 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Installing the new optical drive
NOTE:
If you are installing an optical drive in a bay that did not previously have a drive in it, you
must remove the access panel, the front bezel, and the bezel blank covering the opening of the bay
before proceeding. Follow the procedures in
Removing the computer access panel
on page
100
and
Removing a bezel blank
on page
103
.
1.
Follow the instructions for removing the optical drive if one was installed. Refer to
Removing the
optical drive
on page
111
.
2.
Attach the release latch to the new optical drive. Refer to
Preparing the new optical drive
on page
112
.
3.
Slide the optical drive through the front bezel all the way into the bay so that it locks in place (1),
then connect the cable to the rear of the drive (2).
4.
Replace the computer access panel.
5.
If the computer was on a stand, replace the stand.
6.
Reconnect the power cord and turn on the computer.
7.
Lock any security devices that were disengaged when the computer cover or access panel was
removed.
ENWW
Replacing the optical drive
113