HP Jetdirect 640n HP Jetdirect Print Servers 640n and 695n - Administrator's G - Page 65

Snmp Traps, Ipx/spx, En_8022, En_ii

Get HP Jetdirect 640n PDF manuals and user guides View all HP Jetdirect 640n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Table 3-3 Telnet Commands and Parameters (continued) set-cmnty-name Password to determine which SNMP SetRequests (control functions) the HP Jetdirect print server responds to. The community name of an incoming SNMP SetRequest must match the print server's set community name for the print server to respond. (For additional security, you can limit configuration access through the print server's host access list.) Enter up to 255 alphanumeric characters. default-get-cmnty SNMP Traps auth-trap trap-dest IPX/SPX ipx-config ipx-unitname Address ipx-frametype Default Get community name. 0 Disable. 1 (default): Enable. Disabling this parameter can prohibit communications with SNMP management applications. Send SNMP authentication traps. Authentication traps indicate that an SNMP request was received, but the community name check failed. 0 Disable. 1 (default) Enable. Add a host's IP address to the HP Jetdirect print server's SNMP trap destination list. The list can contain up to six entries. To receive SNMP traps, the listed systems must have a trap daemon that listens for the traps. The following is the command format: trap-dest: [community name] [port number] In the example, is the IP address of the host to receive traps, [community name] specifies the SNMP community name, and [port number] identifies the port number to use. The default community name is public. The default SNMP port number is 162. You must enter a community name to specify a port number. To delete the list, set trap destination to zero (trap-dest: 0). By default, the SNMP trap destination list is empty and the print server does not send SNMP traps. IPX/SPX protocol operation on the print server. 0 Disable. 1 (default): Enable. NOTE: On HP Jetdirect 640n print servers, all network protocols except TCP/IP are disabled by factory default. Name assigned to the print server. Enter up to 31 alphanumeric characters. By default, the name is NPIxxxxxx, where xxxxxx are the last six digits of the LAN hardware address. (Read-only parameter.) The IPX network and node numbers detected on the network, in the form :. IPX frame type settings available for your print server model: AUTO (default), EN_SNAP, EN_8022, EN_8023, EN_II. For more information, see HP Jetdirect configuration pages on page 139. ENWW IPv4 configuration 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
Table 3-3
Telnet Commands and Parameters (continued)
set-cmnty-name
Password to determine which SNMP SetRequests (control functions) the HP Jetdirect
print server responds to. The community name of an incoming SNMP SetRequest must
match the print server's set community name for the print server to respond. (For
additional security, you can limit configuration access through the print server's host
access list.) Enter up to 255 alphanumeric characters.
default-get-cmnty
Default Get community name.
0
Disable.
1
(default): Enable.
Disabling this parameter can prohibit communications with SNMP management
applications.
SNMP Traps
auth-trap
Send SNMP authentication traps. Authentication traps indicate that an SNMP request
was received, but the community name check failed.
0
Disable.
1
(default) Enable.
trap-dest
Add a host's IP address to the HP Jetdirect print server's SNMP trap destination list. The
list can contain up to six entries. To receive SNMP traps, the listed systems must have a
trap daemon that listens for the traps. The following is the command format:
trap-dest: <ip-address> [community name] [port number]
In the example,
<ip-address>
is the IP address of the host to receive traps,
[community name]
specifies the SNMP community name, and
[port number]
identifies the port number to use.
The default community name is public. The default SNMP port number is 162. You must
enter a community name to specify a port number.
To delete the list, set trap destination to zero (
trap-dest: 0
).
By default, the SNMP trap destination list is empty and the print server does not send
SNMP traps.
IPX/SPX
ipx-config
IPX/SPX protocol operation on the print server.
0
Disable.
1
(default): Enable.
NOTE:
On HP Jetdirect 640n print servers, all network protocols except TCP/IP are
disabled by factory default.
ipx-unitname
Name assigned to the print server. Enter up to 31 alphanumeric characters. By default,
the name is NPIxxxxxx, where xxxxxx are the last six digits of the LAN hardware
address.
Address
(Read-only parameter.) The IPX network and node numbers detected on the network, in
the form <network number>:<LAN hardware address>.
ipx-frametype
IPX frame type settings available for your print server model:
AUTO
(default),
EN_SNAP,
EN_8022, EN_8023, EN_II
. For more information, see
HP Jetdirect configuration
pages
on page
139
.
ENWW
IPv4 configuration
55