HP LH4r HP Netserver LH 4 Installation Road Map - Page 6

10 Replace Covers and Cables 1. Replace all covers as described in panel 6: "Removing and Replacing the Covers." 2. Connect the AC power cord and all other cables. CAUTION Replace all covers before operating the NetServer, even for a short time. Otherwise, damage to system components may result due to improper cooling air flow. 11 Verify Installed Accessories (Optional) If you wish, you may now verify accessories you have installed. Turn on power to the HP NetServer and the NOTE monitor, and observe the boot screen. The boot screen lists the hardware, as it is detected, such as CPU, memory, and accessory boards. If the system fails to boot, follow the instructions on the screen. SCSI devices connected to a disk array controller board (DAC), or the integrated NetRAID controller cannot be displayed at boot time, nor can an ISA non-Plug-and-Play board be displayed at boot time. 12 Configure the HP NetServer 1. Turn on the HP NetServer and monitor, insert the HP Navigator CD-ROM into the drive, and press the Reset button. If the system fails to boot, follow the instructions on the screen. NOTE If you have installed an ISA non-Plug-and-Play accessory board, you must reserve system resources for it by using the Setup Utility. Start the Setup Utility by pressing function key [F2] when prompted during the boot process. When the Setup Utility starts, select "Configuration," and then select "ISA non-Plug-and-Play Devices." Use the arrow keys to highlight a selection, press ENTER to display its options, and use the +/- keys to change values. When you've finished, save the changes and exit the utility. For more information about reserving system resources, refer to Information Assistant and to "Configuring an ISA Non-Plug-and-Play Board" in the HP NetServer LH 4 / LH 4r User Guide. (If the system hangs before the Setup Utility starts, remove the ISA non-Plug-and Play board, run the Setup utility to reserve system resources for it, then reinstall the board.) 2. Run Configuration Assistant and Installation Assistant: If you want to change the language, select "Set Preferences" from the HP Navigator main menu and choose a language. Select "Configuration and Installation Assistant." Select "Express" from the next screen to begin the "Express" mode of configuration. "Custom" configuration mode and "Replication" configuration mode are also available. Refer to the HP NetServer LH 4/ LH 4r User Guide for details. 3. Choose a NOS: Select the NOS you will install, and the version, if necessary. Installing the optional Novell® IntranetWare® NOS, which is part of the HP NetServer Software Option Package, requires a decryption key, obtained in panel 5: "Preparation." 4. Select the NOS installation mode: If you select certain versions of Novell® NetWare® / IntranetWare® or Microsoft® Windows™ NT Server, you will be asked, "Would you like to use HP's automated mode of NOS installation?" ! Select "Yes" to choose automated NOS installation for first-time installation of Novell NetWare / IntranetWare or Microsoft Windows NT Server on a factoryconfigured HP NetServer. ! Use the manual NOS installation if you are installing a NOS other than Novell NetWare / IntranetWare or Microsoft Windows NT Server, or if you have replaced accessory components (for example, if you replaced an HP network interface controller board with a thirdparty board that is not on HP's Tested Products List, use the manual NOS installation). 5. View Configuration Advisories: Read the Configuration Advisories and print them if necessary. Make any changes suggested in the advisories. 6. Configure Remote Management: If you plan to manage the HP NetServer LH 4 remotely, refer to the HP NetServer Remote Administrator Guide for instructions. Select "Configure Remote Management" on the Navigator screen to configure Integrated Remote Assistant. 7. Show System Information: Select "View System Information" to get information about accessory boards and devices. Select "View Resources" to view used and available system resources. 8. Configure Mass Storage. This NetServer is shipped with the hotswap mass storage device(s) unconfigured. To configure the drive(s), do one of the following: ! Run HP NetRAID Assistant to configure one or more RAID logical drives. To run HP NetRAID Assistant, select "Execute" from the Configure Disk Array screen. ! Exclude SCSI A Channel from the integrated HP NetRAID controller, as follows: !a. Restart the HP NetServer. !b. Press function key [F2] when prompted. !c. When the SETUP utility menu is displayed, use the up and down arrow keys to highlight the "Include SCSI A Channel [Yes]" selection. !d. Use the + and - keys to change it to "Include SCSI A Channel [No]." !e. Press function key [F10] to save the configuration and exit the utility program. !f. Answer "Yes" to the question "Save Configuration and Exit Now?" The HP NetServer will reboot, and HP Navigator will restart. 9. Install the NOS: If you selected the HP automated NOS installation process, you will be guided through the process by a series of HP display screens: ! Install Utility Partition: This step creates a disk utility partition on the server boot hard disk drive where HP Navigator will copy troubleshooting and other utilities. The utility partition is not available under SCO® UNIX. Select "Execute" on the Install Utility Partition screen to install the partition. ! Execute Card Utilities: Select "Execute" on the Execute Card Utilities screen to run the accessory board configuration utilities. ! Follow the instructions on the screen and in the network operating system's installation instructions to perform the manual NOS installation. ! For Manual NOS Installation Only: Before you perform a manual NOS installation, print out instructions and create NOSspecific drivers diskette(s), as follows: ! A. Create Drivers Diskette(s): On the Create Drivers Diskette(s) screen, select Create Drivers Diskette(s) to create one or more customized diskettes containing HP drivers and configuration files to use when you install the NOS. ! B. Print and Read Instructions: On the Show NOS Installation Instructions screen, select "Save to Disk" to copy the NOS installation instructions to disk. Then print them from disk. Read the instructions first, and then follow them to manually install the NOS. ! Install NOS: ! A. Automated NOS Installation: For certain versions of Novell NetWare / IntranetWare or Microsoft Windows NT Server, Configuration Assistant formats and partitions the hard disk drive. Installation Assistant then guides you through the NOS installation and configures the NOS with the appropriate drivers for the HP-bundled configuration or for network interface cards on HP's Tested Products List. ! B. Manual NOS Installation: Follow the instructions on the screen and the network operating system installation instructions that you printed. 10. Install HP TopTools: Refer to the HP NetServer Server Management Reference Guide, and install HP TopTools. 11. Refer to Information Assistant on the HP NetServer Online Documentation CD-ROM, for further information about your HP