HP LH4r HP Netserver LH 4 Rack Storage/12FC Installation Guide - Page 70

Verify FCArray Card Firmware Version

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

NOTE Follow the instructions in the FCArray Assistant Installation and User Guide to complete the following tasks. 2. Install both FC Array Assistant Server, then Client software. 3. Once the FCArray Assistant Server software is installed, the DACEVENT command must be modified to include the IP address or name of all the client systems used with the server if you want to be notified of controller events that FCArray Assistant monitors. This modification is not required but HP recommends that you make this change at this time. On the current cluster node that you are installing FCArray Assistant edit the DACSCM.CNF file (add IP addresses or names of clients used with the cluster) for the current cluster node that FCArray Assistant is. Verify FCArray Card Firmware Version 1. If not already done, start FCArray Assistant and double-click the desired DAC(s). 2. Logon as "fcarray." 3. Select the controller information button and verify the firmware version. Refer to the Configuration Guide for the correct version. 4. Perform one of the following: • If incorrect, install the Fibre Channel Cluster Software Disk you created earlier in part 1 "What's Needed" into the floppy drive, refer to the FCArray Assistant Installation and User Guide and upgrade the firmware using the Flash Utility. Remove the floppy disk and reboot the system. If correct, or after upgrading the firmware, return to part "5 NetServer Software Setup" of the Installation Guide and perform the "Install. Service Pack for All HP NetServers" procedure. Fibre Channel Supplement to the HP NetServer Microsoft Cluster Installation Guide 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Fibre Channel Supplement to the HP NetServer Microsoft Cluster Installation Guide
11
NOTE
Follow the instructions in the
FCArray Assistant Installation and User Guide
to complete the
following tasks.
2.
Install both FC Array Assistant Server, then Client software.
3.
Once the FCArray Assistant Server software is installed, the DACEVENT command must be modified
to include the IP address or name of all the client systems used with the server if you want to be notified
of controller events that FCArray Assistant monitors.
This modification is not required but HP
recommends that you make this change at this time.
On the current cluster node that you are installing FCArray Assistant edit the DACSCM.CNF file (add
IP addresses or names of clients used with the cluster) for the current cluster node that FCArray
Assistant is.
Verify FCArray Card Firmware Version
1.
If not already done, start FCArray Assistant and double-click the desired DAC(s).
2.
Logon as "fcarray."
3.
Select the controller information button and verify the firmware version.
Refer to the Configuration
Guide for the correct version.
4.
Perform one of the following:
•
If incorrect, install the
Fibre Channel Cluster Software Disk
you created earlier in part 1 "What’s
Needed" into the floppy drive, refer to the FCArray Assistant Installation and User Guide and
upgrade the firmware using the Flash Utility.
Remove the floppy disk and reboot the system.
If correct, or after upgrading the firmware, return to
part "5
NetServer Software Setup" of
the Installation Guide and perform the "Install. Service Pack for All HP NetServers"
procedure.