HP LH4r Installing Caldera eServer on an HP Netserver

HP LH4r - NetServer - 256 MB RAM Manual

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

HP LH4r manual content summary:

  • HP LH4r | Installing Caldera eServer on an HP Netserver - Page 1
    Server 3.1 Installation Guide for HP NetServers NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version M.04.05. If you don't have the M.04.05 version CD-ROM and you're obtaining this document from the HP on systems that support the PAE (Physical
  • HP LH4r | Installing Caldera eServer on an HP Netserver - Page 2
    Name · One or more clean/new hard drives. · Latest system BIOS update. (http://www.hp.com) Installing Caldera OpenLinux Server 3.1 Note: If you receive a message about "Bad partition tables", please choose to initialize all the hard drives. 1. Power on the server, and insert the Caldera OpenLinux
  • HP LH4r | Installing Caldera eServer on an HP Netserver - Page 3
    Video Mode screen, select your video mode. Your system should be able to support 1024x768 @ 70Hz. If you selected VESA installation, you will not see All drives in the system should appear on the Define partitions screen. Disk partitioning will vary depending on the type of services the server will
  • HP LH4r | Installing Caldera eServer on an HP Netserver - Page 4
    all the requested network information. You may set the system to retrieve the information from a DHCP server or you may use static IP. Click Next. 20. At the Set Up Boot Loader screen, . Click Next. 22. If you have a printer attached to your system, you can configure it at this time. Click Next.
  • HP LH4r | Installing Caldera eServer on an HP Netserver - Page 5
    system will now boot. Congratulations! You have just installed Caldera OpenLinux Server 3.1 Remove the CD from the drive. On-Line Information and Software Sources The OpenLinux 3.1 user guide, system administrator guide and developer guide can be installed on your system. Check the list of packages
  • 1
  • 2
  • 3
  • 4
  • 5
Caldera OpenLinux Server 3.1
Installation Guide for HP NetServers
NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version
M.04.05. If you don't have the M.04.05 version CD-ROM and you're obtaining this document from the HP web
site as a reference to install an operating system, be sure to also check the HP web site for the latest available
drivers.
©Copyright Hewlett-Packard Company
(This document is only available in English.)
November 3, 2001 (Rev: 20011103)
Introduction
This document was created by Hewlett-Packard for the purpose of helping you install
Caldera OpenLinux Server 3.1 on your HP NetServer, based on procedures tested by HP.
The objective of this document is to provide the information needed to achieve the
following tasks.
±²
Install Caldera OpenLinux Server 3.1 from CD-ROM.
±²
Configure network settings.
Features
Caldera OpenLinux 3.1 includes the Linux 2.4 kernel, XFree86 4.0, KDE 2, and a
number of security features that significantly enhance OpenLinux out-of-the-box
security. These security-related features include OpenSSL, OpenSSH, Tripwire,
PortSentry, and enhancements to the Apache HTTPD server.
Requirements
CPU
: Caldera OpenLinux 3.1 includes the 2.4 kernel compiled to support up to 64GB of
RAM. As a result the kernel and Caldera OpenLinux will only function on systems that
support the PAE (Physical Address Extensions) standard. Such CPUs include the
following:
±²
Intel Pentium III
±²
Intel Pentium 4
Disk Space
: A full installation of Caldera OpenLinux 3.1 requires 1700 MB.