HP Latex 3100 Site Preparation Guide - Page 23

Computer and networking requirements

Get HP Latex 3100 PDF manuals and user guides View all HP Latex 3100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Measurement E 6.2 m (20 ft 4in) F 1.5 m (4 ft 11 in) NOTE: The ceiling of the room will vary depending on the overhanging crane used. NOTE: This is the recommended working space, it may vary depending on the lifting technique used. WARNING! The zone surrounding the Jumbo Roll Solution should be considered a restricted access area, and signaled accordingly. Only trained personnel should operate within this area. Storage area for materials When planning a storage area for materials used with the printer, thought should not only be given to safety and convenience, but also to the fact that if inks and substrates are not stored in the appropriate temperature and humidity conditions, print results may be adversely affected. The storage area should be of sufficient size to accommodate adequate stocks of substrate rolls and inks. The storage area should be located near the print production area to minimize the lifting and maneuvering of heavy materials. The storage area should have a covered roof. It should be dry, well ventilated and able to provide protection from direct light. It is important that temperature and humidity are maintained within values specified for each substrate type. NOTE: Allow enough (environmentally controlled) space to store the printheads. This is indicated by the directional arrows on the printhead boxes. Storage conditions for substrate rolls Keep substrate rolls in their sealed wrapping material while they are placed in storage. Store substrate rolls vertically to avoid the migration of plasticizers in some materials. Move substrates from the storage area to the print production area at least 24 hours before use, so that they can reach the required moistness and operating temperature. NOTE: HP substrate rolls have a 12 month warranty when the substrate rolls are stored under optimal conditions. The warranty term varies depending upon the material and the manufacturer. Computer and networking requirements Requirements ● Print Care network functionality requires an Outbound connection to all the following addresses without a proxy. This means that an open Internet connection allowing traffic on port 80 is needed. URL *.heleni.me *.hp.com *.symantec.com *.symantecliveupdate.com HTTPS 80 X X X X ENWW Computer and networking requirements 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
Measurement
E
6.2 m (20 ft 4in)
F
1.5 m (4 ft 11 in)
NOTE:
The ceiling of the room will vary depending on the overhanging crane used.
NOTE:
This is the recommended working space, it may vary depending on the lifting technique used.
WARNING!
The zone surrounding the Jumbo Roll Solution should be considered a restricted access area, and
signaled accordingly. Only trained personnel should operate within this area.
Storage area for materials
When planning a storage area for materials used with the printer, thought should not only be given to safety and
convenience, but also to the fact that if inks and substrates are not stored in the appropriate temperature and
humidity conditions, print results may be adversely affected.
The storage area should be of sufficient size to accommodate adequate stocks of substrate rolls and inks. The
storage area should be located near the print production area to minimize the lifting and maneuvering of heavy
materials.
The storage area should have a covered roof. It should be dry, well ventilated and able to provide protection from
direct light. It is important that temperature and humidity are maintained within values specified for each
substrate type.
NOTE:
Allow enough (environmentally controlled) space to store the printheads. This is indicated by the
directional arrows on the printhead boxes.
Storage conditions for substrate rolls
Keep substrate rolls in their sealed wrapping material while they are placed in storage.
Store substrate rolls vertically to avoid the migration of plasticizers in some materials.
Move substrates from the storage area to the print production area at least 24 hours before use, so that they can
reach the required moistness and operating temperature.
NOTE:
HP substrate rolls have a 12 month warranty when the substrate rolls are stored under optimal
conditions. The warranty term varies depending upon the material and the manufacturer.
Computer and networking requirements
Requirements
●
Print Care network functionality requires an
Outbound
connection to all the following addresses
without
a
proxy. This means that an open Internet connection allowing traffic on port 80 is needed.
URL
HTTPS 80
*.heleni.me
X
*.hp.com
X
*.symantec.com
X
*.symantecliveupdate.com
X
ENWW
Computer and networking requirements
19