HP Latex 375 User Guide Latex 3x5 - Page 10

Electrical shock hazard, Heat hazard, Fire hazard, To avoid the risk of fire

Get HP Latex 375 PDF manuals and user guides View all HP Latex 375 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

● There is smoke or an unusual smell coming from the printer. ● The printer has been dropped or the curing module has been damaged. ● The printer is not operating normally. Turn off the printer in either of the following cases: ● During a thunderstorm ● During a power failure Take special care with zones marked with warning labels. Electrical shock hazard WARNING! The internal circuits of curing zones, output drier, print-zone heaters, and built-in power supplies operate at hazardous voltages capable of causing death or serious personal injury. The printer uses two power cords. Unplug both power cords before servicing the printer. To avoid the risk of electric shock: ● The printer must be connected to earthed mains outlets only. ● Do not attempt to dismantle the curing modules. ● Do not remove or open any other closed system covers or plugs. ● Do not insert objects through slots in the printer. Heat hazard The curing subsystems of the printer operate at high temperatures and can cause burns if touched. To avoid personal injury, take the following precautions. ● Do not touch the internal enclosures of the printer's curing zones. ● Let the printer cool down when accessing the internal curing zone and output platen in case of a substrate jam. ● Let the printer cool down before performing some maintenance operations. Fire hazard The curing subsystems of the printer operate at high temperatures. To avoid the risk of fire, take the following precautions. ● The customer is responsible for meeting the printer's requirements and the Electrical Code requirements according to the local jurisdiction of the country where the equipment is installed. Use the power supply voltage specified on the nameplate. ● Connect the power cords to dedicated lines, each protected by a branch circuit breaker according to the information detailed in the site preparation guide. Do not use a power strip (relocatable power tap) to connect both power cords. ● Use only the power cords supplied by HP with the printer. Do not use a damaged power cord. Do not use the power cords with other products. ● Do not insert objects through slots in the printer. 4 Chapter 1 Introduction ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
●
There is smoke or an unusual smell coming from the printer.
●
The printer has been dropped or the curing module has been damaged.
●
The printer is not operating normally.
Turn off the printer in either of the following cases:
●
During a thunderstorm
●
During a power failure
Take special care with zones marked with warning labels.
Electrical shock hazard
WARNING!
The internal circuits of curing zones, output drier, print-zone heaters, and built-in power supplies
operate at hazardous voltages capable of causing death or serious personal injury.
The printer uses two power cords. Unplug both power cords before servicing the printer.
To avoid the risk of electric shock:
●
The printer must be connected to earthed mains outlets only.
●
Do not attempt to dismantle the curing modules.
●
Do not remove or open any other closed system covers or plugs.
●
Do not insert objects through slots in the printer.
Heat hazard
The curing subsystems of the printer operate at high temperatures and can cause burns if touched. To avoid
personal injury, take the following precautions.
●
Do not touch the internal enclosures of the printer's curing zones.
●
Let the printer cool down when accessing the internal curing zone and output platen in case of a substrate
jam.
●
Let the printer cool down before performing some maintenance operations.
Fire hazard
The curing subsystems of the printer operate at high temperatures.
To avoid the risk of fire, take the following precautions.
●
The customer is responsible for meeting the printer's requirements and the Electrical Code requirements
according to the local jurisdiction of the country where the equipment is installed. Use the power supply
voltage specified on the nameplate.
●
Connect the power cords to dedicated lines, each protected by a branch circuit breaker according to the
information detailed in the site preparation guide. Do not use a power strip (relocatable power tap) to
connect both power cords.
●
Use only the power cords supplied by HP with the printer. Do not use a damaged power cord. Do not use
the power cords with other products.
●
Do not insert objects through slots in the printer.
4
Chapter 1
Introduction
ENWW