HP Latex 375 User Guide Latex 3x5 - Page 11

Mechanical hazard, Light radiation hazard, Ventilation

Get HP Latex 375 PDF manuals and user guides View all HP Latex 375 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

● Take care not to spill liquid on the printer. After cleaning, make sure all components are dry before using the printer again. ● Do not use aerosol products that contain flammable gases inside or around the printer. Do not operate the printer in an explosive atmosphere. ● Do not block or cover the openings of the printer. ● Do not attempt to dismantle or modify the curing modules. ● Ensure that the operating temperature of the substrate recommended by the manufacturer is not exceeded. If this information is not available, ask the manufacturer. Do not load substrates that cannot be used at an operating temperature above 125°C (257°F). ● Do not load substrates with auto-ignition temperatures below 250°C (482°F). If this information is not available, printing must be supervised at all times. See note below. NOTE: Test method based on EN ISO 6942:2002; Evaluation of materials and material assemblies when exposed to a source of radiant heat, method B. The test conditions, to determine the temperature when the substrate starts ignition (either flame or glow), were: Heat flux density 30 kW/m², copper calorimeter, K type thermocouple. Mechanical hazard The printer has moving parts that could cause injury. To avoid personal injury, take the following precautions when working close to the printer. ● Keep your clothing and all parts of your body away from the printer's moving parts. ● Avoid wearing necklaces, bracelets, and other hanging objects. ● If your hair is long, try to secure it so that it will not fall into the printer. ● Take care that sleeves or gloves do not get caught in the printer's moving parts. ● Avoid standing close to the fans, which could cause injury and could also affect print quality (by obstructing the air flow). ● Do not touch gears or moving rolls during printing. ● Do not operate the printer with covers bypassed. Light radiation hazard Light radiation is emitted from the illumination of the print zone. This illumination is in compliance with the requirements of the exempt group of IEC 62471:2006, Photobiological safety of lamps and lamp systems. However, you are recommended not to look directly at the LEDs while they are on. Do not modify the module. Chemical hazard See the safety data sheets available at http://www.hp.com/go/msds to identify the chemical ingredients of your consumables. Sufficient ventilation should be provided to ensure that potential airborne exposure to these substances is adequately controlled. Consult your usual air-conditioning or EHS specialist for advice on the appropriate measures for your location. For more detailed information, see the "Ventilation" and "Air conditioning" sections of the site preparation guide, available from http://www.hp.com/go/latex300/manuals/. Ventilation Ensure that the room in which the system is installed meets local environmental, health, and safety (EHS) guidelines and regulations. ENWW Safety precautions 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
●
Take care not to spill liquid on the printer. After cleaning, make sure all components are dry before using
the printer again.
●
Do not use aerosol products that contain flammable gases inside or around the printer. Do not operate the
printer in an explosive atmosphere.
●
Do not block or cover the openings of the printer.
●
Do not attempt to dismantle or modify the curing modules.
●
Ensure that the operating temperature of the substrate recommended by the manufacturer is not
exceeded. If this information is not available, ask the manufacturer. Do not load substrates that cannot be
used at an operating temperature above 125°C (257°F).
●
Do not load substrates with auto-ignition temperatures below 250°C (482°F). If this information is not
available, printing must be supervised at all times. See note below.
NOTE:
Test method based on EN ISO 6942:2002;
Evaluation of materials and material assemblies when
exposed to a source of radiant heat, method B
. The test conditions, to determine the temperature when the
substrate starts ignition (either flame or glow), were: Heat flux density 30 kW/m², copper calorimeter, K type
thermocouple.
Mechanical hazard
The printer has moving parts that could cause injury. To avoid personal injury, take the following precautions
when working close to the printer.
●
Keep your clothing and all parts of your body away from the printer's moving parts.
●
Avoid wearing necklaces, bracelets, and other hanging objects.
●
If your hair is long, try to secure it so that it will not fall into the printer.
●
Take care that sleeves or gloves do not get caught in the printer's moving parts.
●
Avoid standing close to the fans, which could cause injury and could also affect print quality (by obstructing
the air flow).
●
Do not touch gears or moving rolls during printing.
●
Do not operate the printer with covers bypassed.
Light radiation hazard
Light radiation is emitted from the illumination of the print zone. This illumination is in compliance with the
requirements of the exempt group of IEC 62471:2006,
Photobiological safety of lamps and lamp systems
.
However, you are recommended not to look directly at the LEDs while they are on. Do not modify the module.
Chemical hazard
See the safety data sheets available at
go/msds
to identify the chemical ingredients of your
consumables. Sufficient ventilation should be provided to ensure that potential airborne exposure to these
substances is adequately controlled. Consult your usual air-conditioning or EHS specialist for advice on the
appropriate measures for your location. For more detailed information, see the “Ventilation” and “Air
conditioning” sections of the site preparation guide, available from
go/latex300/manuals/
.
Ventilation
Ensure that the room in which the system is installed meets local environmental, health, and safety (EHS)
guidelines and regulations.
ENWW
Safety precautions
5