HP MP3800 Compaq IPAQ Microportable Projector MP3800 - Users Manual - Page 32

Adjusting, Multiple inputs are active. Use the OSD to select the, alternate sources - projector review

Get HP MP3800 - Compaq iPAQ XGA DLP Projector PDF manuals and user guides View all HP MP3800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Using the On-Screen Display Menu ■ Adjusting-Indicates the Resync button has been pressed or the Factory Reset option has been selected from the OSD menu. The message will disappear when the appropriate mode is detected and displayed by the projector. ■ Multiple inputs are active. Use the OSD to select the alternate sources-The projector has detected multiple inputs. This message may appear when powering up, returning from Standby, or when the Source button is pressed on the remote control. If no selection is made within 10 seconds, the currently displayed source will remain as the active source. Press the Source button on the remote control to review and select from the active video sources. ■ Lamp May Fail Soon. Replacement Suggested-Indicates the lamp is approaching failure. The message will remain on the screen for 10 seconds or until the on-screen Menu button is pressed. This message appears once when powering up or returning from Standby until the lamp is replaced. After the lamp is changed, access the Service menu to reset the lamp hours counter. Refer to the "Replacing the Projector Lamp Module" section of Chapter 7 for information on resetting the lamp hours counter. ✎ The 10-second timeout is the default value. To change the timeout value, select the Management menu, select the OSD Timeout menu, and change the timeout from 1 to 40 seconds. ✎ When the projector is started, the Compaq banner displays for approximately 10 seconds. To skip this banner display, turn off the function using the OSD menu. 3-10 Compaq iPAQ Microportable Projector MP3800 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
3–10
Compaq iPAQ Microportable Projector MP3800 User’s Guide
Using the On-Screen Display Menu
■
Adjusting—
Indicates the
Resync
button has been pressed or
the Factory Reset option has been selected from the OSD
menu. The message will disappear when the appropriate
mode is detected and displayed by the projector.
■
Multiple inputs are active. Use the OSD to select the
alternate sources
—The projector has detected multiple
inputs. This message may appear when powering up,
returning from Standby, or when the
Source
button is pressed
on the remote control. If no selection is made within 10
seconds, the currently displayed source will remain as the
active source. Press the
Source
button on the remote control to
review and select from the active video sources.
■
Lamp May Fail Soon. Replacement Suggested
—Indicates
the lamp is approaching failure. The message will remain on
the screen for 10 seconds or until the on-screen
Menu
button is
pressed. This message appears once when powering up or
returning from Standby until the lamp is replaced. After the
lamp is changed, access the Service menu to reset the lamp
hours counter. Refer to the “Replacing the Projector Lamp
Module” section of Chapter 7 for information on resetting the
lamp hours counter.
✎
The 10-second timeout is the default value. To change the timeout
value, select the Management menu, select the OSD Timeout
menu, and change the timeout from 1 to 40 seconds.
✎
When the projector is started, the Compaq banner displays for
approximately 10 seconds. To skip this banner display, turn off
the function using the OSD menu.