HP MSL4048 HP StorageWorks MSL2024, MSL4048 Tape Library Fibre Channel Referen - Page 11

HP StorageWorks MSL4048 tape library - storageworks password

Get HP MSL4048 - StorageWorks Ultrium 920 Tape Library PDF manuals and user guides
UPC - 882780742215
View all HP MSL4048 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

HP StorageWorks MSL4048 tape library NOTE: HP recommends that you cable Port A only and that you configure Port B for Auto Detect on Fibre Speed and Port Type. 1. Highlight Configuration -> Drive 1 and press OK. 2. Enter the Administrative password if prompted. 3. Use the navigation buttons to move to the Port A Fibre Speed. Press OK. 4. Use the navigation buttons to change the value of the highlighted field (Auto Detect, 1 Gb or 2 Gb). When the highlighted field shows the desired value, press OK. 5. Use the navigation buttons to move to the Port A Type field and repeat Step 4 to specify the port type (Auto Detect, Fabric (N) or Loop (NL)) 6. If you have selected Fabric (N) or Auto Detect, configuration is now complete, go to Step 8. a. If you selected port type Loop (NL), move to the Port A Loop Mode field and repeat Step 4 to specify the required mode (Soft, Hard or Hard Auto Select). 7. If you have selected Soft or Hard Auto Select, configuration is now complete, go to Step 8. a. If you have selected Hard, use the navigation buttons to move to the Port A ALPA field and repeat Step 4 to specify the address. 8. Use the navigation buttons to select Port B Fibre Speed and Port B Type, making sure they are set to Auto Detect. 9. Use the navigation buttons to move to the area and press OK to carry out the configuration (or move to the area and press OK to cancel the operation). Figure 7 MSL4048 Operator Control Panel 10. MSL2024, MSL4048 Tape Library Fibre Channel reference guide 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
MSL2024, MSL4048 Tape Library Fibre Channel reference guide
9
HP StorageWorks MSL4048 tape library
NOTE:
HP recommends that you cable Port A only and that you configure Port B for
Auto Detect
on
Fibre
Speed
and
Port Type
.
1.
Highlight
Configuration ->
Drive 1
and press
OK
.
2.
Enter the Administrative password if prompted.
3.
Use the navigation buttons to move to the
Port A Fibre Speed.
Press
OK
.
4.
Use the navigation buttons to change the value of the highlighted field (Auto Detect, 1 Gb or 2 Gb).
When the highlighted field shows the desired value, press
OK
.
5.
Use the navigation buttons to move to the
Port A Type
field and repeat Step 4 to specify the port type
(Auto Detect, Fabric (N) or Loop (NL))
6.
If you have selected Fabric (N) or Auto Detect, configuration is now complete, go to Step 8.
a.
If you selected port type Loop (NL), move to the
Port A Loop Mode
field and repeat Step 4 to
specify the required mode (Soft, Hard or Hard Auto Select).
7.
If you have selected Soft or Hard Auto Select, configuration is now complete, go to Step 8.
a.
If you have selected Hard, use the navigation buttons to move to the
Port A ALPA
field and repeat
Step 4 to specify the address.
8.
Use the navigation buttons to select
Port B Fibre Speed
and
Port B Type,
making sure they
are set to
Auto Detect.
9.
Use the navigation buttons to move to the
<Save>
area and press
OK
to carry out the configuration (or
move to the
<Cancel>
area and press
OK
to cancel the operation).
Figure 7
MSL4048 Operator Control Panel
10.