HP OMEN Notebook - 15t-5000 HP OMEN Notebook PC 15 Maintenance and Service Gui - Page 34

Solid-state drive (M.2

Get HP OMEN Notebook - 15t-5000 PDF manuals and user guides View all HP OMEN Notebook - 15t-5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Solid-state drive (M.2) Description 128 GB solid-state drive (SSD), M.2, TLC 256 GB solid-state drive (SSD), M.2, MLC 512 GB solid-state drive (SSD), M.2, MLC Spare part number 788611001 788612-001 788613-001 Before removing the solid-state drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 23). 5. Disconnect the battery (see Disconnecting the battery on page 25). Remove the solid-state drive: 1. Remove the Phillips PM2.0×3.5 screw (1) that secures the solid-state drive to the system board. 2. Remove the solid-state drive (2) by pulling the drive away from the slot at an angle. Reverse this procedure to install the solid-state drive. 28 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
Solid-state drive (M.2)
Description
Spare part number
128 GB solid-state drive (SSD), M.2, TLC
788611001
256 GB solid-state drive (SSD), M.2, MLC
788612-001
512 GB solid-state drive (SSD), M.2, MLC
788613-001
Before removing the solid-state drive, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
23
).
5.
Disconnect the battery (see
Disconnecting the battery
on page
25
).
Remove the solid-state drive:
1.
Remove the Phillips PM2.0×3.5 screw
(1)
that secures the solid-state drive to the system board.
2.
Remove the solid-state drive
(2)
by pulling the drive away from the slot at an angle.
Reverse this procedure to install the solid-state drive.
28
Chapter 5
Removal and replacement procedures for Authorized Service Provider parts