HP Pavilion 14-al100 Maintenance and Service Guide - Page 51

Solid-state drive, Remove the solid-state drive

Get HP Pavilion 14-al100 PDF manuals and user guides View all HP Pavilion 14-al100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Solid-state drive Description 256-GB, M2.2280, SATA-3 128-GB, M2.2280, SATA-3 Spare part number 865902-005 827560-015 Before removing the solid-state drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 32). 5. Disconnect the battery cable from the system board (see Battery on page 34). Remove the solid-state drive: 1. Remove the Phillips PM2.0×3.8 screw (1) that secures the solid-state drive to the computer. (The solid- state drive tilts up.) 2. Remove the solid-state drive (2) by pulling the drive away from the slot at an angle. Reverse this procedure to install the solid-state drive. Component replacement procedures 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Solid-state drive
Description
Spare part number
256-GB, M2.2280, SATA-3
865902-005
128-GB, M2.2280, SATA-3
827560-015
Before removing the solid-state drive, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer
on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
32
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
34
).
Remove the solid-state drive:
1.
Remove the Phillips PM2.0×3.8 screw
(1)
that secures the solid-state drive to the computer. (The solid-
state drive tilts up.)
2.
Remove the solid-state drive
(2)
by pulling the drive away from the slot at an angle.
Reverse this procedure to install the solid-state drive.
Component replacement procedures
43