HP Pavilion TouchSmart 11-e110nr HP Pavilion 11 Notebook PC HP Pavilion TouchS - Page 77

detach it., the system board components

Get HP Pavilion TouchSmart 11-e110nr PDF manuals and user guides View all HP Pavilion TouchSmart 11-e110nr manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

f. Fan (see Fan on page 62) g. System board (see System board on page 64) Remove the heat sink: 1. Turn the system board upside down, with the front toward you. 2. Following the 1 through 4 sequence stamped into the heat sink, loosen the four captive Phillips PM2.0×2.5 screws (1) that secure the heat sink to the system board. 3. Remove the heat sink (2). NOTE: Due to the adhesive quality of the thermal material located between the heat sink and the system board components, it may be necessary to move the heat sink from side to side to detach it. NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system board components each time the heat sink is removed. Thermal paste is used on the processor (1) and the heat sink section (2) that services it Component replacement procedures 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
f.
Fan (see
Fan
on page
62
)
g.
System board (see
System board
on page
64
)
Remove the heat sink:
1.
Turn the system board upside down, with the front toward you.
2.
Following the 1 through 4 sequence stamped into the heat sink, loosen the four captive Phillips
PM2.0×2.5 screws
(1)
that secure the heat sink to the system board.
3.
Remove the heat sink
(2)
.
NOTE:
Due to the adhesive quality of the thermal material located between the heat sink and
the system board components, it may be necessary to move the heat sink from side to side to
detach it.
NOTE:
The thermal material must be thoroughly cleaned from the surfaces of the heat sink and
the system board components each time the heat sink is removed. Thermal paste is used on the
processor
(1)
and the heat sink section
(2)
that services it
Component replacement procedures
67