HP Pavilion zt3100 HP and Compaq Notebook Series - Bluetooth Users Guide - Page 30

Network Access

Get HP Pavilion zt3100 - Notebook PC PDF manuals and user guides View all HP Pavilion zt3100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

BTW User's Guide 3.6.8 Network Access The Bluetooth Network Access service makes it possible for a remote Bluetooth device to access a Local Area Network that is physically attached to this computer or allows a remote device to become part of an ad hoc network provided by this computer. After this computer has been configured to provide the Network Access service to other Bluetooth devices, it will not be able to use the Bluetooth Network Access service provided by another Bluetooth device without being re-configured. Put another way, this computer cannot be both a Bluetooth Network Access server and a Bluetooth Network Access client at the same time. 3.6.8.1 Setup for Windows 98SE & Windows Me NOTE: Internet Protocol routing software is required on Windows 98SE and Windows Me servers. Install and configure the routing software as instructed by the software's manufacturer. Configure the server: 1. From the Windows Control Panel, double-click the Network icon. 2. On the Configuration tab, select TCP/IP > Bluetooth LAN Access Server Driver (scroll down if necessary). 3. Click Properties and select the IP Address tab. a) Select Specify an IP address. b) Enter an IP Address (suggested value-192.168.1.1). c) Enter a Subnet Mask (suggested value-255.255.255.0). 4. Click OK twice to close the dialog boxes and then click Yes to restart the computer. 3.6.8.2 Setup for Windows 2000 and Windows XP If Internet Connection sharing was previously enabled (before BTW was installed), it must be disabled and then re-enabled before the Bluetooth network adapter can use it. Configure for Network Access: 1. From the Windows system tray, right-click the Bluetooth icon and select Advanced Configuration from the shortcut menu. 2. In the Bluetooth configuration panel, select the Local Services tab, Network Access and then click Properties... 3. From the Network Access, General properties page: in the Type of service shortcut menu, select "Allow other devices to access the Internet/LAN via this computer," and then click Configure Connection Sharing. 4. Perform the following Steps: Windows XP: ! Right-click Local Area Connection, select Properties and then select the Advanced tab, Sharing check box. Windows 2000: ! Right-click Local Area Connection, select Properties and then select the Sharing tab. ! Select Enable Internet Connection Sharing for this connection, click OK, and then click YES in the confirmation dialog box. WIDCOMMinc 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
BTW User’s Guide
WIDCOMMinc
26
3.6.8
Network Access
The Bluetooth Network Access service makes it possible for a remote Bluetooth device
to access a Local Area Network that is physically attached to this computer or allows a
remote device to become part of an ad hoc network provided by this computer.
After this computer has been configured to provide the Network Access service to other
Bluetooth devices, it will not be able to use the Bluetooth Network Access service
provided by another Bluetooth device without being re-configured. Put another way, this
computer cannot be both a Bluetooth Network Access server and a Bluetooth Network
Access client at the same time.
3.6.8.1 Setup for Windows 98SE & Windows Me
NOTE: Internet Protocol routing software is required on Windows 98SE and Windows Me
servers.
Install and configure the routing software as instructed by the software°s
manufacturer.
Configure the server:
1.
From the Windows Control Panel, double-click the Network icon.
2.
On the Configuration tab, select TCP/IP > Bluetooth LAN Access Server Driver
(scroll down if necessary).
3.
Click Properties and select the IP Address tab.
a)
Select Specify an IP address.
b)
Enter an IP Address (suggested value´192.168.1.1).
c)
Enter a Subnet Mask (suggested value´255.255.255.0).
4.
Click OK twice to close the dialog boxes and then click Yes to restart the
computer.
3.6.8.2 Setup for Windows 2000 and Windows XP
If Internet Connection sharing was previously enabled (before BTW was installed), it
must be disabled and then re-enabled before the Bluetooth network adapter can use it.
Configure for Network Access:
1.
From the Windows system tray, right-click the Bluetooth icon and select
Advanced Configuration from the shortcut menu.
2.
In the Bluetooth configuration panel, select the Local Services tab, Network
Access and then click Properties...
3.
From the Network Access, General properties page: in the Type of service
shortcut menu, select ±Allow other devices to access the Internet/LAN via this
computer,² and then click Configure Connection Sharing.
4.
Perform the following Steps:
Windows XP:
!
Right-click Local Area Connection, select Properties and then select the
Advanced tab, Sharing check box.
Windows 2000:
!
Right-click Local Area Connection, select Properties and then select the
Sharing tab.
!
Select Enable Internet Connection Sharing for this connection, click OK, and
then click YES in the confirmation dialog box.