HP ProSignia 500 Compaq ProSignia Family of PC Servers Maintenance and Service - Page 26

Automatic Data Recovery, need Automatic Data

Get HP ProSignia 500 PDF manuals and user guides View all HP ProSignia 500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Data Recovery is in progress. 1779-Slot # Drive Array Intermittent drive If this message Replacement drive(s) failure and/or appears and drive X detected OR previously possible loss of has not been replaced, failed drive now appears data. this indicates an to be operational: Drive intermittent drive X. Restore data from failure. This message backup if replacement also appears once drive has been installed. immediately following drive replacement whenever data must be restored from backup. 1780-Disk 0 Failure Hard drive/format Run Diagnostics. error. Replace failed assembly as indicated or, contact your service provider. Error Code Probable Source Action of Problem 1781-Disk 1 Failure Hard drive/format Run Diagnostics. error. Replace failed assembly as indicated or, contact your service provider. 1782-Disk Controller Hard disk drive Run Diagnostics. circuitry error. Replace failed assembly as indicated or, contact your service provider. 1783-Slot # Drive Array Drive Array If message appears Controller Failure Controller is following a ROM defective or not installation, ROM is installed properly. defective or not installed properly. Otherwise, replace the IDA-2. 1784-Slot # Drive Array Defective drive Check for loose cables. Drive Failure, Physical and/or cables. Replace defective drive drive replacement X and/or cable(s). needed: Drive X 1785-Slot # Drive Array Configuration error. Run the EISA Not Configured Configuration Utility and correct. 1786-Drive Array Interim Data Recovery Press F1 key to allow Recovery Needed mode. Data has not Automatic Data Recovery The following drive(s) been recovered yet. to begin. Data will need Automatic Data automatically be Recovery: Drive X. restored to drive X Select "F1" to continue now that the drive has with recovery of data been replaced or now to drive(s). Select "F2" seems to be working. to continue without -Or- recovery of data to Press the F2 key and the

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Data Recovery is in
progress.
---------------------------------------------------------------------------
1779-Slot # Drive Array
Intermittent drive
If this message
Replacement drive(s)
failure and/or
appears and drive X
detected OR previously
possible loss of
has not been replaced,
failed drive now appears
data.
this indicates an
to be operational: Drive
intermittent drive
X. Restore data from
failure. This message
backup if replacement
also appears once
drive has been installed.
immediately following
drive replacement
whenever data must be
restored from backup.
---------------------------------------------------------------------------
1780-Disk 0 Failure
Hard drive/format
Run Diagnostics.
error.
Replace failed assembly
as indicated or, contact
your service provider.
---------------------------------------------------------------------------
Error Code
Probable Source
Action
of Problem
---------------------------------------------------------------------------
1781-Disk 1 Failure
Hard drive/format
Run Diagnostics.
error.
Replace failed assembly
as indicated or, contact
your service provider.
---------------------------------------------------------------------------
1782-Disk Controller
Hard disk drive
Run Diagnostics.
circuitry error.
Replace failed assembly
as indicated or, contact
your service provider.
---------------------------------------------------------------------------
1783-Slot # Drive Array
Drive Array
If message appears
Controller Failure
Controller is
following a ROM
defective or not
installation, ROM is
installed properly.
defective or not
installed properly.
Otherwise, replace the
IDA-2.
---------------------------------------------------------------------------
1784-Slot # Drive Array
Defective drive
Check for loose cables.
Drive Failure, Physical
and/or cables.
Replace defective drive
drive replacement
X and/or cable(s).
needed: Drive X
---------------------------------------------------------------------------
1785-Slot # Drive Array
Configuration error.
Run the EISA
Not Configured
Configuration Utility
and correct.
---------------------------------------------------------------------------
1786-Drive Array
Interim Data Recovery
Press F1 key to allow
Recovery Needed
mode. Data has not
Automatic Data Recovery
The following drive(s)
been recovered yet.
to begin. Data will
need Automatic Data
automatically be
Recovery: Drive X.
restored to drive X
Select "F1" to continue
now that the drive has
with recovery of data
been replaced or now
to drive(s). Select "F2"
seems to be working.
to continue without
-Or-
recovery of data to
Press the F2 key and the