HP Stream 14-z000 HP Stream Notebook PC - Maintenance and Service Guide - Page 42

Display assembly

Get HP Stream 14-z000 PDF manuals and user guides View all HP Stream 14-z000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

4. Install thermal paste on the following components: Thermal paste is used on the processor (1) and the heat sink (2). Reverse this procedure to install the heat sink. Display assembly NOTE: The display assembly is spared at the subcomponent level only. For more display assembly spare part information, see the individual removal subsections. Before replacing the display assembly, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the keyboard/top cover (see Keyboard/top cover on page 19). Remove the display assembly: 1. Disconnect the display panel cable (1) from the system board. 2. Disconnect the WLAN antenna cable (2) from the terminal on the WLAN module. 3. Release the WLAN antenna cable from the clip (3) built into the base enclosure. 4. Remove the two Phillips PM1.9×2.8 screws (4) that secure the display assembly system board to the base enclosure. 36 Chapter 4 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
4.
Install thermal paste on the following components:
Thermal paste is used on the processor
(1)
and the heat sink
(2)
.
Reverse this procedure to install the heat sink.
Display assembly
NOTE:
The display assembly is spared at the subcomponent level only. For more display assembly spare
part information, see the individual removal subsections.
Before replacing the display assembly, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the keyboard/top cover (see
Keyboard/top cover
on page
19
).
Remove the display assembly:
1.
Disconnect the display panel cable
(1)
from the system board.
2.
Disconnect the WLAN antenna cable
(2)
from the terminal on the WLAN module.
3.
Release the WLAN antenna cable from the clip
(3)
built into the base enclosure.
4.
Remove the two Phillips PM1.9×2.8 screws
(4)
that secure the display assembly system board to the
base enclosure.
36
Chapter 4
Removal and replacement procedures for Authorized Service Provider parts